- 您现在的位置：买卖IC网 > PDF目录11500 > 127-0711-601 (Emerson Network Power Connectivity Johnson)CONN SMP MALE HERMETIC SEAL PDF资料下载
参数资料
| 型号： | 127-0711-601 |
| 厂商： | Emerson Network Power Connectivity Johnson |
| 文件页数： | 15/20页 |
| 文件大小： | 0K |
| 描述： | CONN SMP MALE HERMETIC SEAL |
| 产品目录绘图： | 127-(0,1,2)711-601 |
| 特色产品： | SMP Blind-Mate Connectors |
| 标准包装： | 5 |
| 系列： | SMP |
| 附件类型： | 真空密封 |
| 适用于相关产品： | SMP 连接器 |
| 特点： | 全方位锁销 |
| 其它名称： | J10018 |
Connectivity for
Business-Critical Continuity
SMP Connectors
Assembly Instructions
SMP Right Angle Female Solder Style for .047 OD Semi-Rigid Cable
1. Identify tools (5 piece parts) and connector parts (3 piece parts).
2. Strip cable jacket and dielectric to dimension shown. Do not
nick center conductor. Clean all debris from prepared cable.
3. Insert center conductor into cable stop as shown. Make sure
slot in connector contact is aligned with cross hole in body as
shown. Insert cable into cross hole in connector body, making
sure cable stop bottoms out against internal shoulder of
connector body.
4. Insert connector assembly into interface location fixture and
clamp cable in vise using body holder fixture as shown. Tighten
stop screw until light pressure is applied between connector
body, cable stop and cable jacket.
5. Solder contact to center conductor through rear access port in
connector body using a minimum amount of solder and heat for a
good joint.
6. After center conductor solder joint has cooled, solder connector
body to cable jacket, using a minimum amount of solder and heat
for a full fillet joint. Take care so that solder does not flow onto
anti-rock ring or into rear access port. Allow assembly to cool
before removing connector from vise and location fixture.
7. Using a fixture plate as shown, press end cap into rear access
port using a .156 (3.96) diameter flat punch until fully seated
within body counter bore.
8. Best results are obtained when contact location is flush to .004
(0.10) recessed from reference plane. Interface location fixture
is pre-set at factory, but can be adjusted to control location.
Cable Group
MIL-C-17/151, .047 Semi-Rigid
Tool
Cable Vise
Stop Screw
Clamp Inserts
Body Holder
Interface Location Fixture
Part Number
127-0692-101
Part Number
140-0000-962
140-0000-981
140-0000-997
127-0000-904
127-0000-903
15
相关PDF资料 |
PDF描述 |
|---|---|
| PIC16F913-E/ML | IC PIC MCU FLASH 4KX14 28QFN |
| ADG719BRTZ-REEL7 | IC SWITCH SPDT SOT23-6 |
| PIC24FV16KA301-E/SO | IC MCU 16B 16KB FLASH 20SOIC |
| ADG702BRJZ-REEL7 | IC SWITCH SPST SOT23-5 |
| VI-B3B-CU-F2 | CONVERTER MOD DC/DC 95V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 12-7071-CARD | 制造商:GC Electronics 功能描述: |
| 127072 | 制造商:Brady Corporation 功能描述:B401 10X14 BLK/ORG WARNING DO NOT ENTER |
| 12-7072 | 制造商:GC Electronics 功能描述: |
| 127073 | 制造商:Brady Corporation 功能描述:B302 10X14 BLK/ORG WARNING DO NOT ENTER |
| 12-7073 | 制造商:GC Electronics 功能描述:Micro Round Nose Pliers |
发布紧急采购，3分钟左右您将得到回复。