- 您现在的位置：买卖IC网 > PDF目录364081 > 12864-12-BN-R-ET-ELP (Electronic Theatre Controls, Inc.) 128 x 64 Dot STN Graphic LCD Assembly With T-6963C Graphics Controller LED / EL Panel Backlight PDF资料下载
参数资料
| 型号： | 12864-12-BN-R-ET-ELP |
| 厂商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 128 x 64 Dot STN Graphic LCD Assembly With T-6963C Graphics Controller LED / EL Panel Backlight |
| 中文描述： | 128 × 64点阵超扭曲液晶显示大会与T - 6963C图形控制器的LED /冷光片背光 |
| 文件页数： | 29/31页 |
| 文件大小： | 477K |
| 代理商： | 12864-12-BN-R-ET-ELP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY MODULE
MODEL NO: 12864-12
5. PRECAUTIONS FOR USING LCD MODULES
Installing LCD Modules
The hole in the printed circuit board is used to fix LCM as shown in the picture below. Attend to the following items when
installing the LCM.
1)
Cover the surface with a transparent protective plate to protect the polarizer and LC cell.
PACIFIC DISPLAY DEVICES
07.21.2006
29
2)
When assembling the LCM into other equipment, the spacer to the bit between the LCM and the fitting plate
should have enough height to avoid causing stress to the module surface, refer to the individual specifications for
measurements. The measurement tolerance should be
±
0.1mm.
Precaution for Handing LCD Modules
Since LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or
making any alterations or modifications to it.
1)
Cover the surface with a transparent protective plate to protect the polarizer and LC cell.
2)
Do not alter, modify or change the shape of the tab on the metal frame.
3)
Do not make extra holes on the printed circuit board, modify its shape or change the positions of components to
be attached.
4)
Do not damage or modify the pattern writing on the printed circuit board.
5)
Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector.
6)
Except for soldering the interface, do not make any alterations or modifications with a soldering iron.
7)
Do not drop, bend or twist LCM.
Electro-Static Discharge Control
Since this module uses a CMOS LSI, the same careful attention should be paid to electrostatic discharge as for an ordinary
CMOS IC.
1)
Make certain that you are grounded when handing LCM.
2)
Before remove LCM from its packing case or incorporating it into a set, be sure the module and your body have
the same electric potential.
3)
When soldering the terminal of LCM, make certain the AC power source for the soldering iron does not leak.
4)
When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to minimize
as much as possible any transmission of electromagnetic waves produced sparks coming from the commutator of
the motor.
5)
As far as possible make the electric potential of your work clothes and that of the work bench the ground
potential.
6)
To reduce the generation of static electricity be careful that the air in the work is not too dried. A relative
humidity of 50%-60% is recommended.
Precaution for soldering to the LCM
1)
Observe the following when soldering lead wire, connector cable and etc. to the LCM.
a)
Soldering iron temperature : 280
°
C
±
10
°
C.
b)
Soldering time : 3-4 sec.
2)
Solder : eutectic solder.
相关PDF资料 |
PDF描述 |
|---|---|
| 12864-12-BN-R-ST-ELED | 128 x 64 Dot STN Graphic LCD Assembly With T-6963C Graphics Controller LED / EL Panel Backlight |
| 12864-12-BN-R-ST-ELP | 128 x 64 Dot STN Graphic LCD Assembly With T-6963C Graphics Controller LED / EL Panel Backlight |
| 12864-12-FC-F-ET-ELED | 128 x 64 Dot STN Graphic LCD Assembly With T-6963C Graphics Controller LED / EL Panel Backlight |
| 12864-12-FC-F-ET-ELP | 128 x 64 Dot STN Graphic LCD Assembly With T-6963C Graphics Controller LED / EL Panel Backlight |
| 12864-12-FC-F-ST-ELED | 128 x 64 Dot STN Graphic LCD Assembly With T-6963C Graphics Controller LED / EL Panel Backlight |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 12864-12-BN-R-ST-ELED | 制造商:未知厂家 制造商全称:未知厂家 功能描述:128 x 64 Dot STN Graphic LCD Assembly With T-6963C Graphics Controller LED / EL Panel Backlight |
| 12864-12-BN-R-ST-ELP | 制造商:未知厂家 制造商全称:未知厂家 功能描述:128 x 64 Dot STN Graphic LCD Assembly With T-6963C Graphics Controller LED / EL Panel Backlight |
| 12864-12-FC-F-ET-ELED | 制造商:未知厂家 制造商全称:未知厂家 功能描述:128 x 64 Dot STN Graphic LCD Assembly With T-6963C Graphics Controller LED / EL Panel Backlight |
| 12864-12-FC-F-ET-ELP | 制造商:未知厂家 制造商全称:未知厂家 功能描述:128 x 64 Dot STN Graphic LCD Assembly With T-6963C Graphics Controller LED / EL Panel Backlight |
| 12864-12-FC-F-ST-ELED | 制造商:未知厂家 制造商全称:未知厂家 功能描述:128 x 64 Dot STN Graphic LCD Assembly With T-6963C Graphics Controller LED / EL Panel Backlight |
发布紧急采购，3分钟左右您将得到回复。