- 您现在的位置：买卖IC网 > PDF目录18529 > 1490413-4 (TE Connectivity)NEST U-DIE SOLISTRAND #2 PDF资料下载
参数资料
| 型号： | 1490413-4 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/7页 |
| 文件大小： | 0K |
| 描述： | NEST U-DIE SOLISTRAND #2 |
| 标准包装： | 1 |
| 系列： | Solistrand |
| 压接或电缆尺寸： | 2 AWG |
| 压接手柄： | 1490748-1，1490749-1 |
| 连接器类型： | 端子及连接件 |
| 相关产品： | 1976230-1-ND - HYDRAULIC CRIMPING HEAD ASS Y 1490746-1-ND - TOOL 14 TON CRIMPING HEAD 1490749-1-ND - CRIMP TOOL HYDRAULIC |
408- 8691
Die Release
Button
Nest
Indenter
4. WIRE STRIPPING AND CRIMPING PROCEDURES
4.1. Wire Stripping
Strip wire to the dimensions listed in Figure 4. Do
NOT nick or cut the wire strands.
Die
Release
Button
Ram
(Advanced)
Figure 3
8. Refer to Paragraph 5.1, Crimp Inspection, for
standard terminal, butt splice, and parallel splice
crimp inspection.
5. INSPECTION/MAINTENANCE
4.2. Crimping Procedure
DANGER To avoid personal injury, be sure to exercise
caution while holding terminals, splices or wire
near the crimping area of power units.
DANGER
To avoid personal injury, disconnect the power
supply before performing maintenance,
adjustments, inspections and repairs.
5.1. Crimp Inspection (Figure 6)
i
1. Ensure that the wire range or size stamped on
the terminal or splice corresponds with the wire
size being used and the wire range or size
stamped on the nest and indenter.
2. Center terminal or splice in nest as shown in
Figure 5. For best results, when brazed seam on
terminal or splice is visible, position seam toward
indenter.
3. Activate power unit so that ram advances and
holds terminal or splice in place. Do NOT deform
terminal or splice wire barrel.
4. Insert stripped wire into terminal or parallel
splice until end of conductor is flush with or
extended slightly beyond end of wire barrel.
5. Insert stripped wire into butt splice until end of
conductor butts against splice wire stop.
6. Activate power unit to complete the crimp.
NOTE The accompanying procedure is included as an
aid to the tool operator ONLY. It is not intended to
serve as a quality control procedure for qualifying
finished crimps on SOLISTRAND terminals or
splices.
Inspect crimped terminals or splices by checking the
features described in Figure 6. Use only terminals or
splices that meet the conditions shown in the
ACCEPT column. Terminals and splices displaying
the features shown in the REJECT column can be
avoided by careful use of these instructions and by
performing the maintenance and inspection
procedures described in Paragraphs in 5.2 and 5.3.
5.2. Daily Maintenance
It is recommended that each operator of the dies be
made aware of, and responsible for, the following
steps of daily maintenance:
NOTE
i
If terminal sticks in die after crimping, grasp wire
close to crimp and apply a rocking motion to
remove from die.
1. Remove dust, moisture, and other contaminants
from the dies with a clean brush, or a clean, soft,
lint--free cloth. Do NOT use objects that could
damage the dies.
7. For butt splice, repeat steps 5 and 6 for other
wire barrel.
Rev F
2. If dies are coated with oil or preservative, wipe
clean — particularly in the crimping areas —
before placing them in use.
3 of 7
相关PDF资料 |
PDF描述 |
|---|---|
| GLAA01A1B-Q07 | SWITCH ROTARY SIDE |
| EVU-F3AF30B14 | POT 10K OHM 9MM VERT NO BUSHING |
| 46-502-A-07 | SWITCH PUSH SPDT 0.25A 115V |
| B82725A2202N1 | COIL CHOKE 18MH 2.0A RADIAL |
| NTD6600NT4G | MOSFET N-CH 100V 12A DPAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1490413-5 | 功能描述:冲压机与冲模 NEST U-DIE SOLIS 1/0 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1490413-6 | 功能描述:冲压机与冲模 NEST U-DIE SOLIS 2/0 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1490413-7 | 功能描述:冲压机与冲模 NEST U-DIE SOLIS 3/0 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1490413-8 | 功能描述:冲压机与冲模 NEST U-DIE SOLIS 4/0 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1490413-9 | 功能描述:冲压机与冲模 NEST U-DIE SOLIS #HD RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
发布紧急采购，3分钟左右您将得到回复。