- 您现在的位置：买卖IC网 > PDF目录18529 > 1490413-4 (TE Connectivity)NEST U-DIE SOLISTRAND #2 PDF资料下载
参数资料
| 型号： | 1490413-4 |
| 厂商： | TE Connectivity |
| 文件页数： | 5/7页 |
| 文件大小： | 0K |
| 描述： | NEST U-DIE SOLISTRAND #2 |
| 标准包装： | 1 |
| 系列： | Solistrand |
| 压接或电缆尺寸： | 2 AWG |
| 压接手柄： | 1490748-1，1490749-1 |
| 连接器类型： | 端子及连接件 |
| 相关产品： | 1976230-1-ND - HYDRAULIC CRIMPING HEAD ASS Y 1490746-1-ND - TOOL 14 TON CRIMPING HEAD 1490749-1-ND - CRIMP TOOL HYDRAULIC |
408- 8691
3
1
Terminal
ACCEPT
REJECT
Terminal
1
4
4
Terminal
Wire Range
Stamped
Under Tongue
2
3
Wire Range
Stamped
Under Tongue
2
1
4
4
5
Parallel
Splice
1
3
Sight or Standard
Hole Type
3
6
1
3
4
1
3
4
Butt Splice
5
Wire Range
Stamped Here
2
Strap
Type
Wire Range
Stamped Here
2
1
Crimped off end of splice or terminal wire barrel.
1
2
3
4
5
Crimps centered. Crimps may be off center BUT NOT OFF
END OF WIRE BARREL.
AWG wire size being used matches wire range or size
stamped on terminal or splice and dies.
Insulation does not enter wire barrel.
Wire is visible through inspection hole of butt splices. Wire is
flush with or extends slightly beyond end of terminal wire
barrel.
On parallel splices, bare wire ends must be flush with
or extended slightly beyond end of barrel.
2
3
4
5
6
AWG wire size being used does not match wire size or
range stamped on terminal or splice and dies.
Insulation entered barrel of terminal or splice. CHECK
FOR INCORRECT STRIP LENGTH.
Wire not inserted far enough in terminal or splice. End of
wire must be visible through inspection hole of butt splices,
and be flush with or extend slightly beyond end of terminal
wire barrel or parallel splice.
Excessive “flash” on terminal or splice indicates damaged
dies or wrong wire, splice, or tooling combination was used.
Nicked or missing strands.
Figure 6
3. When dies are not in use, make certain all
surfaces are protected with a THIN coat of any
good SAE 20 motor oil, and mate and store them
in a clean, dry area.
5.3. Periodic Inspection
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the dies or be made available to
supervisory personnel responsible for the dies.
Though recommendations call for at least a monthly
inspection, the inspection frequency should be based
upon the amount of use, working conditions, operator
Rev F
training and skill, and established company
standards. These inspections should be performed in
the following sequence:
A. Visual Inspection (Figure 7)
1. Remove all lubrication and accumulated film by
immersing the dies in a suitable degreaser that will
not affect paint or plastic.
2. Check all surfaces for wear. Inspect the crimp
area for flattened, chipped, cracked, worn, or
broken areas. If damage is evident, the die must
be replaced.
5 of 7
相关PDF资料 |
PDF描述 |
|---|---|
| GLAA01A1B-Q07 | SWITCH ROTARY SIDE |
| EVU-F3AF30B14 | POT 10K OHM 9MM VERT NO BUSHING |
| 46-502-A-07 | SWITCH PUSH SPDT 0.25A 115V |
| B82725A2202N1 | COIL CHOKE 18MH 2.0A RADIAL |
| NTD6600NT4G | MOSFET N-CH 100V 12A DPAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1490413-5 | 功能描述:冲压机与冲模 NEST U-DIE SOLIS 1/0 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1490413-6 | 功能描述:冲压机与冲模 NEST U-DIE SOLIS 2/0 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1490413-7 | 功能描述:冲压机与冲模 NEST U-DIE SOLIS 3/0 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1490413-8 | 功能描述:冲压机与冲模 NEST U-DIE SOLIS 4/0 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 1490413-9 | 功能描述:冲压机与冲模 NEST U-DIE SOLIS #HD RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
发布紧急采购，3分钟左右您将得到回复。