- 您现在的位置：买卖IC网 > Datasheet目录593 > 1490746-1 (TE Connectivity)TOOL 14 TON CRIMPING HEAD Datasheet资料下载
参数资料
| 型号： | 1490746-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/3页 |
| 文件大小： | 0K |
| 描述： | TOOL 14 TON CRIMPING HEAD |
| 标准包装： | 1 |
| 配用： | 1752681-3-ND - INDENT U-DIE SOLIS FLAG 6-2AWG 1752681-2-ND - INDENT U-DIE SOLIS FLAG 8AWG 1752681-1-ND - INDENT U-DIE SOLS FLAG 1/0-4/0 1752680-8-ND - NEST U-DIE SOLISTRAND FLAG 8AWG 1752680-7-ND - NEST U-DIE SOLISTRAND FLAG 6AWG 1752680-6-ND - NEST U-DIE SOLISTRAND FLAG 4AWG 1752680-5-ND - NEST U-DIE SOLISTRAND FLAG 2AWG 1752680-4-ND - NEST U-DIE SOLISTRAND FLAG 1/0 1752680-3-ND - NEST U-DIE SOLISTRAND FLAG 2/0 1752680-2-ND - NEST U-DIE SOLISTRAND FLAG 3/0 更多... |
| 相关产品： | 1804700-2-ND - PUMP HYDRAULIC HEAVY DUTY 1804700-1-ND - PUMP HYDRAULIC HEAVY DUTY 1583661-1-ND - HAND HYDRAULIC PUMP 1583659-1-ND - FOOT HYDRAULIC PUMP |
Hydraulic Crimping Head 1490746- 1
3.2. Die Installation
DANGER To avoid personal injury, do NOT accidentally
depress the footswitch or handle control when
installing or removing dies.
CAUTION Operating the head WITHOUT the crimping dies
installed will damage the “C”--Head or ram.
!
Install the dies as described in the appropriate die
instruction sheet. Refer to Figure 2.
4. CRIMPING PROCEDURE
The following procedure provides only general
information concerning crimping. Refer to the
instructions packaged with the dies (see
Figure 2) and power unit for detailed information,
including wire stripping dimensions and instructions
for positioning terminals and splices in the dies.
1. Insert terminal or splice in the stationary die
according to the instructions packaged with the
dies.
2. Activate the power unit to advance the dies and
hold the terminal or splice in place.
3. Insert stripped wire into the terminal or splice.
4. Activate the power unit to complete the crimp.
5. INSPECTION/MAINTENANCE
408- 8714
Once a year, or every 7,500 cycles (whichever comes
first), the hydraulic head should be returned to Tyco
Electronics for magnetic particle inspection.
Additionally, inspect and service the head (as
described in Figure 3) every month or 1,000 cycles,
whichever comes first. Refer to Figure 1.
5.1. Cleaning
Remove accumulations of dirt and grease on the
crimping head, especially in areas where dies are
installed and terminals are crimped. Clean the entire
head frequently with a clean, lint--free cloth.
5.2. Visual Inspection
In addition to the inspections listed in Figure 3,
inspect the head for nicks, scratches, and cracks.
Inspect for cracks especially at the corners of the
“C“--head and around the top of the cylinder. Refer to
Figure 4.
Inspect the metal surfaces for nicks, cracks,
scratches, and excessive wear, especially where
sliding contact occurs.
5.3. Crimping Head Check- Out Procedure
If the ram fails to retract after completion of a
crimping cycle, the cause may be in the crimping
head. To determine whether or not the trouble is in
the crimping head, release pressure in the power unit.
If the ram retracts, the trouble is not in the crimping
head. If ram does NOT retract, refer to Section 6,
RETURN/REPAIR.
6. RETURN/REPAIR
DANGER
Make sure hydraulic pressure is released and
power supply is disconnected before following
inspection and maintenance procedures, unless
otherwise specified in the procedure.
Order replacement parts through your Tyco
Electronics representative, or call 1--800--526--5142,
or send a facsimile of your purchase order to
1--717--986--7605, or write to:
Each crimping head is assembled and inspected
before shipment. It is recommended that the crimping
head be inspected immediately upon its arrival at your
facility, and at regularly scheduled intervals, to ensure
that the crimping head has not been damaged during
handling. Frequency of inspection depends upon the
following:
CUSTOMER SERVICE (38--35)
TYCO ELECTRONICS CORPORATION
P.O. BOX 3608
HARRISBURG, PA 17105--3608
Crimping heads may also be returned for evaluation
and repair. For tool repair service, contact a Tyco
Electronics representative at 1--800--526--5136.
S
S
S
S
Care, amount of use, and handling of the head;
Type and size of products crimped;
Degree of operator skill; and
Environmental conditions.
7. REVISION SUMMARY
S Updated document to corporate requirements
S Added ORIGINAL INSTRUCTIONS
2 of 3
Tyco Electronics Corporation
Rev A
相关PDF资料 |
PDF描述 |
|---|---|
| 14A-56-10 | XFRMR PWR 115/230V 5VAC 11.2A |
| 14A-56-515 | XFRMR PWR 115/230V 5V 3A 56VA |
| 1534858-1 | STORAGE BOX SOLARLOK-BAG ASSY |
| 1579001-3 | TOOL DIE SET FOR UMNL TERMINALS |
| 1579001-4 | TOOL DIE SET FOR MQS 1.2MM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1490747-1 | 功能描述:折皱器 CRIMPING HEAD 12 TON TITANIUM RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 1490747-2 | 制造商:TE Connectivity 功能描述:12 TON TITANIUM CRIMPING HEAD - Bulk |
| 1490748-1 | 功能描述:折皱器 1" COMPRESSION TOOL RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 1490749-1 | 功能描述:折皱器 AMP CRIMP TOO RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 1490751-1 | 功能描述:手工工具 GUARD,GRIPPER, G-TERM VERSION RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
发布紧急采购，3分钟左右您将得到回复。