- 您现在的位置：买卖IC网 > Datasheet目录594 > 1583518-1 (TE Connectivity)TOOL ARBOR FRAME WITH SLIDE Datasheet资料下载
参数资料
| 型号： | 1583518-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | TOOL ARBOR FRAME WITH SLIDE |
| 标准包装： | 1 |
| 系列： | * |
408- 8812
Ram Stop
Collar
NOTE
i
The polarization legs of the connector must
engage with the connector locator. The connector
locator should engage with the and return to a
vertical position.
Ensure that the connector is loaded correctly
before proceeding.
CAUTION
!
If the connector is not loaded correctly, damage
to the connector will result.
2. With the connector properly loaded, install the
desired wire into the wire holding combs. Repeat
installation of wires until all wires have been
loaded.
i
Figure 5
Special Setup Procedure for Discrete Wire
Select the desired wire size, and load into wire
holding comb. If the comb retains the wire proceed
with termination (Section 6). If wire comb does not
hold discrete wire, remove the comb retaining screws
and flip combs over to opposite side. Then tighten
comb retaining screws and load wire for test fit.
Install connector as described in Section 6, and pull
the handle until the upper tooling contacts the
connector housing. The upper tooling should just
touch top of connector housing. If the upper tooling
damages the connector, adjust the ram stop collar to
limit the stroke of the arbor frame terminator.
6. TERMINATION PROCEDURE
3. Slide the fixture underneath upper tooling, and
rotate handle until upper tooling is fully seated.
Raise upper tooling, and slide fixture to front end
stop.
4. Remove the wires from the combs being careful
not to disturb contacts.
5. Depress the handle on connector locator and
carefully remove terminated connector from the
fixture by lifting straight ”up.”
CAUTION Do not twist the terminated connector during
unloading, or damage may result.
!
6.2. Terminating Ribbon Cable
NOTE For closed--end ribbon cable applications, it is
important that the cable is cut square. Refer to
product application specification 114--13072.
6.1. Terminating Discrete Wire
1. Depress the handle on the connector locator
and install connector as shown in Figure 6.
Connector
NOTE
i
For feed--through ribbon cable terminations, be
sure to remove the cable stop.
Polarization Leg
Connector Locator
Discrete Wire Lower Tooling
Discrete Wire Comb
Figure 6
Rev A
3 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 1583662-3 | HYDRAULIC HOSE ASSEMBLY 20 FT. |
| 1583684-2 | DIE SET D CONN SIZE 9.0 |
| 1583696-1 | DIE SET MMCX USE WITH A9996-ND |
| 1586343-1 | TOOL EXTRACTION PE SERIES |
| 1586344-1 | TOOL EXTRACTION MICRO MATENLOK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1583526 | 功能描述:重负荷电源连接器 VC-TFS 6-PE RoHS:否 制造商:Hirose Connector 系列:PS2 产品类型:Connectors 位置/触点数量: 端接类型:Crimp 触点材料: 触点电镀:Gold 电压额定值: 电流额定值:300 A 附件类型: |
| 1583527-1 | 功能描述:手工工具 626 SDE ADAPTER NORM RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 158353027 | 功能描述:LED Lighting WL-SWTC White, Warm 2700K 3.2V 350mA 120° 2-SMD, No Lead, Exposed Pad 制造商:wurth electronics inc 系列:WL-SWTC 包装:剪切带（CT） 零件状态:有效 颜色:暖白色 CCT（K）:2700K 85°C 时通量，电流 - 测试:- 25°C 时通量，电流 - 测试:95 lm（标准） 电流 - 测试:350mA 电压 - 正向（Vf）（典型值）:3.2V 不同测试电流时的流明/瓦:85 lm/W CRI（高显色指数）:80（标准） 电流 - 最大值:1A 视角:120° 安装类型:表面贴装 封装/外壳:2-SMD，无引线，裸露焊盘 封装热阻:8°C/W 标准包装:1 |
| 158353030 | 功能描述:LED Lighting WL-SWTC White, Warm 3000K 3.2V 350mA 120° 2-SMD, No Lead, Exposed Pad 制造商:wurth electronics inc 系列:WL-SWTC 包装:剪切带（CT） 零件状态:有效 颜色:暖白色 CCT（K）:3000K 85°C 时通量，电流 - 测试:- 25°C 时通量，电流 - 测试:95 lm（标准） 电流 - 测试:350mA 电压 - 正向（Vf）（典型值）:3.2V 不同测试电流时的流明/瓦:85 lm/W CRI（高显色指数）:80（标准） 电流 - 最大值:1A 视角:120° 安装类型:表面贴装 封装/外壳:2-SMD，无引线，裸露焊盘 封装热阻:8°C/W 标准包装:1 |
| 158353040 | 功能描述:LED Lighting WL-SWTC White, Neutral 4000K 3.2V 350mA 120° 2-SMD, No Lead, Exposed Pad 制造商:wurth electronics inc 系列:WL-SWTC 包装:剪切带（CT） 零件状态:有效 颜色:中性白 CCT（K）:4000K 85°C 时通量，电流 - 测试:- 25°C 时通量，电流 - 测试:110 lm（标准） 电流 - 测试:350mA 电压 - 正向（Vf）（典型值）:3.2V 不同测试电流时的流明/瓦:98 lm/W CRI（高显色指数）:75（标准） 电流 - 最大值:1A 视角:120° 安装类型:表面贴装 封装/外壳:2-SMD，无引线，裸露焊盘 封装热阻:8°C/W 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。