参数资料
| 型号： | 1650152-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 12/17页 |
| 文件大小： | 0K |
| 描述： | CONN PIN #8 CRIMP SILVER |
| 标准包装： | 250 |
| 系列： | ELCON |
| 类型： | 功率 |
| 引脚或插口： | 引脚 |
| 触点终端： | 压接 |
| 包装： | 散装 |
| 其它名称： | A101770 |
114-13206
E. PC Board Hole Dimensions
The solder type contacts may be used with or without plated through holes. If plated, the drilled hole size,
plating types, and plating thickness are dependent on the application requirements. The finished hole size
must be as stated to provide unrestricted insertion and ensure adequate application of solder to the solder
tines. See Figure 9.
Trace Width (As Required)
Pad Width (As Required)
Drilled Hole Diameter
(As Required)
Finished Hole Diameter After
Plating (Refer to Table)
CONTACT SIZE
20
16
12?
8
Copper Plating (Ref)
(Max Hardness 150 Knoop)
Tin-Lead Plating (Ref)
Plating Recommendations:
Tin Plate 0.005 mm [.0002 in.] Min. Thick
Over Copper 0.025 mm [.0010 in.] Thick
FINISHED HOLE DIAMETER (+0.08 [+.003])
1.20 [.047]
1.80 [.070]
2.65 [.104]
3.82 [.152]
i NOTE Hold-downs may be used to ensure stability during the soldering procedure.
?Includes hot plug contacts
Figure 9
3.12. Connector Seating
The connector standoffs must be seated on the pc board or panel not exceeding the dimension shown in
Figure 10.
NOTE
0.51
[.020]
0.51
[.020]
Connector
PC Board (Ref)
Standoffs
Wire
Figure 10
3.13. Soldering
Observe guidelines and procedures when soldering contacts is required. All solder joints should conform to
those specified in Workmanship Specification IPC-A-610 and all other requirements specified in this document.
Contacts must be stabilized during soldering with a non-metallic material. Solder, clean, and dry all wire leads to
contacts according to the following:
Rev E
12 of 17
相关PDF资料 |
PDF描述 |
|---|---|
| 1766196-1 | CONN CONTACT PIN #12 CRIMP |
| 1766195-1 | CONN PIN SIZE #12 CRIMP |
| 1766193-1 | CONN PIN #12 CRIMP SILVER |
| 166722-1 | CONN SOCKET CRIMP 22-26AWG GOLD |
| DSPIC33FJ128GP802-E/SP | IC DSPIC MCU/DSP 128K 28DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1650152-4 | 功能描述:重负荷电源连接器 701-11-02109 CONTACT PIN #8 RoHS:否 制造商:Hirose Connector 系列:PS2 产品类型:Connectors 位置/触点数量: 端接类型:Crimp 触点材料: 触点电镀:Gold 电压额定值: 电流额定值:300 A 附件类型: |
| 1650153-1 | 制造商:TE CONNECTIVITY 功能描述:701-12-02107=CONTACT,PIN, |
| 1650153-2 | 功能描述:电源到板 CONTACT PIN #12 RoHS:否 制造商:TE Connectivity / AMP 系列:5787444 产品类型:Connectors 触点类型: 电压额定值:50 V 电流额定值: 节距: 位置/触点数量:5 安装风格:Through Hole 端接类型: 触点电镀:Tin |
| 1650153-2 | 制造商:TE Connectivity 功能描述:CONTACT PIN CRIMP |
| 1650153-7 | 功能描述:重负荷电源连接器 701-12-02109 CONTACT PIN #12 RoHS:否 制造商:Hirose Connector 系列:PS2 产品类型:Connectors 位置/触点数量: 端接类型:Crimp 触点材料: 触点电镀:Gold 电压额定值: 电流额定值:300 A 附件类型: |
发布紧急采购，3分钟左右您将得到回复。