- 您现在的位置：买卖IC网 > Datasheet目录595 > 1976230-1 (TE Connectivity)HYDRAULIC CRIMPING HEAD ASS Y Datasheet资料下载
参数资料
| 型号： | 1976230-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/8页 |
| 文件大小： | 0K |
| 描述： | HYDRAULIC CRIMPING HEAD ASS Y |
| 标准包装： | 1 |
| 配用： | 1752681-3-ND - INDENT U-DIE SOLIS FLAG 6-2AWG 1752681-2-ND - INDENT U-DIE SOLIS FLAG 8AWG 1752681-1-ND - INDENT U-DIE SOLS FLAG 1/0-4/0 1752680-8-ND - NEST U-DIE SOLISTRAND FLAG 8AWG 1752680-7-ND - NEST U-DIE SOLISTRAND FLAG 6AWG 1752680-6-ND - NEST U-DIE SOLISTRAND FLAG 4AWG 1752680-5-ND - NEST U-DIE SOLISTRAND FLAG 2AWG 1752680-4-ND - NEST U-DIE SOLISTRAND FLAG 1/0 1752680-3-ND - NEST U-DIE SOLISTRAND FLAG 2/0 1752680-2-ND - NEST U-DIE SOLISTRAND FLAG 3/0 更多... |
| 相关产品： | 1804700-2-ND - PUMP HYDRAULIC HEAVY DUTY 1804700-1-ND - PUMP HYDRAULIC HEAVY DUTY 1583661-1-ND - HAND HYDRAULIC PUMP 1583659-1-ND - FOOT HYDRAULIC PUMP |
The preferred (first) method is:
1. Insert properly stripped wire fully into splice.
Figure 5
2. Position splice in die assembly so that edge of
die is within width of splice crimp mark. The stripe
marking on splice must be inside die, facing up,
and in alignment with dot on nest. See Figure 6.
The alternate second method is:
1. Position terminal in stationary die (nest) with
back of tongue resting against die.
3. Holding wire in place, activate power unit to
complete first splice crimp.
4. When crimp is completed, remove the splice.
2. The wire is not inserted into the terminal.
Instead, Jog to advance the ram to hold the
terminal. This is difficult to do; If the terminal barrel
is deformed, the wire may not be inserted properly.
3. Insert properly stripped wire fully into terminal.
4. Holding wire in place, activate power unit to
complete crimp.
5. Remove crimped terminal from the die
assembly. See Figure 5 for information on where to
grip break away terminals when removing them
from the die assembly.
5. To crimp other half of splice, rotate the
splice/tool 180 , making sure the stripe marking on
the splice is inside the assembly, facing up, and in
alignment with dot on nest. See Figure 6. Follow
the same procedure used to crimp first side of
splice (steps 1 through 4).
The alternate (second) method is slightly different, but
very important. The difference is in preceding Step 1.
1. Position splice in die assembly so that edge of
die is within width of splice crimp mark. The stripe
marking on splice must be inside die, facing up,
and in alignment with dot on nest. See Figure 6.
2. Do NOT insert wire into splice, instead, jog to
advance the ram to hold the splice. This is difficult
to do; If the splice is deformed, the wire may not be
inserted properly.
3. Insert properly stripped wire fully into splice wire
barrel.
相关PDF资料 |
PDF描述 |
|---|---|
| 1981944-1 | CABLE CAT5E STRIPPER |
| 2-1105870-8 | TOOL DIE SET - HSK,HSM,HSS CONT |
| 2-1579007-1 | EXTRACTION TOOL |
| 2-1611461-1 | TRANSFORMER OUTLINE 7/8 120VAC |
| 2-229378-3 | MI-1 TOOL (CHAMP) IEEE 1-PC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1976250000 | 制造商:Weidmuller 功能描述:SC 3.81/13/135G 3.2SN GN BX |
| 1976250-2 | 制造商:TE Connectivity 功能描述:BATTERY TOOL KIT, T-HEAD - Bulk |
| 1976250-4 | 制造商:TE Connectivity 功能描述:BATTERY TOOL KIT, T-HEAD - Bulk |
| 1976-2520-A-22 | 制造商:RAF Electronic Hardware 功能描述: |
| 1976260-2 | 制造商:TE Connectivity 功能描述:BATTERY TOOL KIT, T-HEAD - Bulk |
发布紧急采购，3分钟左右您将得到回复。