- 您现在的位置：买卖IC网 > Datasheet目录595 > 1976230-1 (TE Connectivity)HYDRAULIC CRIMPING HEAD ASS Y Datasheet资料下载
参数资料
| 型号： | 1976230-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 5/8页 |
| 文件大小： | 0K |
| 描述： | HYDRAULIC CRIMPING HEAD ASS Y |
| 标准包装： | 1 |
| 配用： | 1752681-3-ND - INDENT U-DIE SOLIS FLAG 6-2AWG 1752681-2-ND - INDENT U-DIE SOLIS FLAG 8AWG 1752681-1-ND - INDENT U-DIE SOLS FLAG 1/0-4/0 1752680-8-ND - NEST U-DIE SOLISTRAND FLAG 8AWG 1752680-7-ND - NEST U-DIE SOLISTRAND FLAG 6AWG 1752680-6-ND - NEST U-DIE SOLISTRAND FLAG 4AWG 1752680-5-ND - NEST U-DIE SOLISTRAND FLAG 2AWG 1752680-4-ND - NEST U-DIE SOLISTRAND FLAG 1/0 1752680-3-ND - NEST U-DIE SOLISTRAND FLAG 2/0 1752680-2-ND - NEST U-DIE SOLISTRAND FLAG 3/0 更多... |
| 相关产品： | 1804700-2-ND - PUMP HYDRAULIC HEAVY DUTY 1804700-1-ND - PUMP HYDRAULIC HEAVY DUTY 1583661-1-ND - HAND HYDRAULIC PUMP 1583659-1-ND - FOOT HYDRAULIC PUMP |
6. To crimp other half of splice, rotate the
splice/tool 180 , making sure the stripe marking on
splice is inside the assembly, facing up, and in
alignment with dot on nest. See Figure 6. Follow
the same procedure used to crimp first side of
splice (Steps 1 through 5).
A crimp inspection mark is featured on each crimped
terminal or splice. The mark consists of a dimple on
the face of a cylinder which is embossed in the
primary crimp area of the terminal or splice. The
inspection mark must appear as shown in the artwork
presented in Section 3.5 of Application Specification
114–2134.
The inspection mark must appear as indicated in
Application Specification 114–2134, in order to qualify
the terminal or splice as an acceptable termination.
The terminal or splice is unacceptable and should be
rejected if the identification mark is deformed.
If the mark is deformed, refer to Figure 3 of this
instruction sheet to verify proper wire CMA and
terminal/die combination.
Verify that crimping dies fully bottom during crimp
cycle. Also, determine if dies are in proper
configuration by gaging the crimp chamber specified
in Paragraph 5.2.B.
Figure 6
These instructions have been approved by Tyco
Electronics Design, Production, and Quality Control
Engineers to provide documented maintenance and
inspection procedures. Through Tyco Electronics test
laboratories and the inspection of production
assembly, the procedures described herein have
been established to ensure the quality and reliability
of crimping die assemblies.
4. Holding wire in place, activate power unit again
to complete crimp.
5. When crimp is completed, remove the splice.
Customer–replaceable parts are listed in Figure 7. A
complete inventory should be stocked and controlled
to prevent lost time when replacement of parts is
necessary.
Die assemblies are inspected before shipment. It is
recommended that the die assembly be inspected
immediately upon arrival at your facility to ensure that
it has not been damaged during shipment.
相关PDF资料 |
PDF描述 |
|---|---|
| 1981944-1 | CABLE CAT5E STRIPPER |
| 2-1105870-8 | TOOL DIE SET - HSK,HSM,HSS CONT |
| 2-1579007-1 | EXTRACTION TOOL |
| 2-1611461-1 | TRANSFORMER OUTLINE 7/8 120VAC |
| 2-229378-3 | MI-1 TOOL (CHAMP) IEEE 1-PC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1976250000 | 制造商:Weidmuller 功能描述:SC 3.81/13/135G 3.2SN GN BX |
| 1976250-2 | 制造商:TE Connectivity 功能描述:BATTERY TOOL KIT, T-HEAD - Bulk |
| 1976250-4 | 制造商:TE Connectivity 功能描述:BATTERY TOOL KIT, T-HEAD - Bulk |
| 1976-2520-A-22 | 制造商:RAF Electronic Hardware 功能描述: |
| 1976260-2 | 制造商:TE Connectivity 功能描述:BATTERY TOOL KIT, T-HEAD - Bulk |
发布紧急采购，3分钟左右您将得到回复。