参数资料
| 型号： | 20-101-0453 |
| 厂商： | Rabbit Semiconductor |
| 文件页数： | 15/30页 |
| 文件大小： | 0K |
| 描述： | MODULE RABBITCORE RCM2300 |
| 标准包装： | 1 |
| 系列： | RabbitCore® |
| 模块/板类型： | MPU 核心模块 |
| 适用于相关产品： | RCM2300 |
| 产品目录页面： | 620 (CN2011-ZH PDF) |
| 其它名称： | 316-1089 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
18
RabbitCore RCM2300
3.4 Starting Dynamic C
Once the RabbitCore module is set up and connected as described in Chapter 2 and
Dynamic C has been installed, start Dynamic C by double-clicking on the Dynamic C
icon. Dynamic C should start, then look for the target system on the COM port you speci-
fied during installation (by default, COM1). Once detected, Dynamic C should go through
a sequence of steps to cold-boot the module and compile the BIOS.
If you receive the message beginning "BIOS successfully compiled and
loaded…"
you are ready to continue with the sample programs in the next section.
3.4.1 Communication Error Messages
If you receive the message "No Rabbit Processor Detected" the programming
cable may be connected to a different COM port, a connection may be faulty, or the target
system may not be powered up. First, check to see that the power LED on the Prototyping
Board is lit. If it is, check both ends of the programming cable to ensure that it is firmly
plugged into the PC and the RCM2300’s programming port, with the pin-1 edge of the
cable matched to the pin-1 mark on the board. If you are using the Prototyping Board,
ensure that the module is firmly and correctly installed in its connectors.
If there are no faults with the hardware, select a different COM port within Dynamic C.
From the Options menu, select Project Options, then select Communications. The
dialog shown should appear.
Select another COM port from the list, then click OK. Press <Ctrl-Y> to force Dynamic C
to recompile the BIOS. If Dynamic C still reports it is unable to locate the target system,
repeat the above steps until you locate the active COM port.
If you receive the “BIOS successfully compiled …” message after pressing <Ctrl-Y> or
starting Dynamic C, and this message is followed by a communications error message, it
is possible that your PC cannot handle the 115,200 bps baud rate. Try changing the baud
rate to 57,600 bps as follows.
Locate the Serial Options dialog in the Dynamic C Options > Project Options >
Communications
menu. Change the baud rate to 57,600 bps. Then press <Ctrl-Y> or
restart Dynamic C.
相关PDF资料 |
PDF描述 |
|---|---|
| 20-101-1235 | CORE MODULE RCM5700 |
| 11FMN-BMTTR-A-TB | CONN FMN HSNG 11POS STAG REV SMD |
| 046232103103800+ | CONN FFC/FPC 3POS 1MM R/A SMD |
| 15FE-ST-VK-N | CONN FFC 15POS RA 1.25MM |
| 09FMN-BMTR-A-TB | CONN FMN HOUSNG 9POS SGL REV SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 20-101-0454 | 功能描述:模块化系统 - SOM RCM2200 RABBITCORE RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 20-101-0455 | 功能描述:单板计算机 BL2010 RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 20-101-0456 | 功能描述:单板计算机 BL2020 RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 20-101-0457 | 功能描述:单板计算机 BL2030 Board RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 20-101-0461 | 功能描述:单板计算机 BL2100 RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
发布紧急采购，3分钟左右您将得到回复。