参数资料
| 型号： | 20-101-0453 |
| 厂商： | Rabbit Semiconductor |
| 文件页数： | 4/30页 |
| 文件大小： | 0K |
| 描述： | MODULE RABBITCORE RCM2300 |
| 标准包装： | 1 |
| 系列： | RabbitCore® |
| 模块/板类型： | MPU 核心模块 |
| 适用于相关产品： | RCM2300 |
| 产品目录页面： | 620 (CN2011-ZH PDF) |
| 其它名称： | 316-1089 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
8
RabbitCore RCM2300
2.2.2 Prototyping Board Expansion
The Prototyping Board comes with several unpopulated areas, which may be filled with
components to suit the user’s development needs. After you have experimented with the
sample programs in Section 3.5, you may wish to expand the Prototyping Board’s capabil-
ities for further experimentation and development. Refer to the Prototyping Board sche-
matic (090–0122) for details as necessary.
Module Extension Headers
—The complete pin set of both the master and slave mod-
ules is duplicated at these two sets of headers. Developers can solder wires directly into
the appropriate holes, or, for more flexible development, 0.1" pitch 26-pin header strips
can be soldered into place. See Figure 1 for the header pinouts.
RS-232
—Two 2-wire or one 5-wire RS-232 serial port can be added to the Prototyping
Board by installing an RS-232 driver IC and four capacitors. The Maxim MAX232CPE
driver chip or a similar device is recommended for U2. Refer to the Prototyping Board
schematic for additional details.
A 10-pin 0.1-inch spacing header strip can be installed at J6 to permit connection of a
ribbon cable leading to a standard DE-9 serial connector.
All RS-232 port components mount to the top side of the Prototyping Board below and
to the left of the MASTER module position.
NOTE: The RS-232 chip, capacitors and header strip are available from electronics dis-
tributors such as Digi-Key.
Prototyping Board Component Header
—Four I/O pins from the RCM2300 module
are hard-wired to the Prototyping Board LEDs and switches through JP1 on the under-
side of the Prototyping Board.
To disconnect these devices and permit
the pins to be used for other purposes, cut
the traces between the pin rows of JP1.
Use a knife or similar tool to cut or break
the traces crossing JP1 in the area
between the silk-screened arrows, as
indicated in Figure 3.
Use jumpers across the positions on
JP1 if you need to reconnect any of the
devices later on.
Figure 3. Prototyping Board Header JP1
(located on BOTTOM SIDE of board)
Cut
PE1 PE7 PB2 PB3
JP1
DS2 DS3 S2 S3
相关PDF资料 |
PDF描述 |
|---|---|
| 20-101-1235 | CORE MODULE RCM5700 |
| 11FMN-BMTTR-A-TB | CONN FMN HSNG 11POS STAG REV SMD |
| 046232103103800+ | CONN FFC/FPC 3POS 1MM R/A SMD |
| 15FE-ST-VK-N | CONN FFC 15POS RA 1.25MM |
| 09FMN-BMTR-A-TB | CONN FMN HOUSNG 9POS SGL REV SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 20-101-0454 | 功能描述:模块化系统 - SOM RCM2200 RABBITCORE RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 20-101-0455 | 功能描述:单板计算机 BL2010 RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 20-101-0456 | 功能描述:单板计算机 BL2020 RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 20-101-0457 | 功能描述:单板计算机 BL2030 Board RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
| 20-101-0461 | 功能描述:单板计算机 BL2100 RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm |
发布紧急采购，3分钟左右您将得到回复。