- 您现在的位置：买卖IC网 > Datasheet目录595 > 220015-3 (TE Connectivity)TOOL HAND CRIMP HEAVY HEAD Datasheet资料下载
参数资料
| 型号： | 220015-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 1/6页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMP HEAVY HEAD |
| 标准包装： | 3 |
| 系列： | Certi-Crimp |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 同轴，RF - BNC，N，TNC |
| 特点： | 侧面插入，棘齿 |
Heavy Head Hand Crimping
Tools (HHHT) 220015-[ ]
Instruction Sheet
408-2331
19 APR 12 Rev C
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use
and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
Adjustment Cap
Front of Tool
Ferrule
Crimping Area
Integral Crimping Dies
CERTI-CRIMP*
Hand Crimping Tool
Ratchet Control
Figure 1
Right Side
of Tool
Center Contact
Crimping Area
Dimensions on this sheet are in metric units
[followed by U.S. customary units in brackets].
i
1. INTRODUCTION
This instruction sheet covers application and
maintenance procedures for Heavy Head Hand
Crimping Tools 220015-[ ]. Refer to Figure 1. The hand
tools are used to crimp a variety of coaxial connectors
with flexible cable. For applicable connector part
numbers and corresponding cable sizes, refer to
Catalog 1307191. Information pertaining to the
connectors (cable stripping dimensions and assembly
of component parts) is included in instructions
packaged with the connectors. Read all instructions
thoroughly before proceeding.
NOTE
Figures and illustrations are for identification only
and are not drawn to scale.
Reasons for reissue are provided in Section 6,
REVISION SUMMARY.
2. DESCRIPTION
Each tool features integral dies that have two crimping
areas (one to crimp the center contact, and one to
crimp the ferrule), an adjustment cap that rotates the
locator-stop (as required), and a CERTI-CRIMP hand
crimping tool ratchet control which ensures full
crimping. Once engaged, the ratchet will not release
until the tool handles have been FULLY closed.
The FRONT of the tool is marked with the part
number. The center contact enters the crimping area
from the RIGHT side of the tool. The contact/cable
assembly is inserted through the BACK of the tool for
ferrule crimping.
3. ASSEMBLY AND CRIMPING PROCEDURES
Select the appropriate cable and connector for the
tool. Slip ferrule over cable; then strip cable to the
proper length, according to instructions packaged with
the connector (plug or jack).
3.1. Crimping the Center Contact
Refer to Figure 2 and proceed as follows:
1. Determine contact type (long or short) from the
dimensions provided in Figure 2. Rotate locator/
stop by turning adjustment cap to OPEN position for
long-type contacts, or CLOSED position for short-
type contacts.
?2012 Tyco Electronics Corporation, a TE Connectivity Ltd. company
All Rights Reserved
*Trademark
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
1 of 6
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or company names may be trademarks of their respective owners.
相关PDF资料 |
PDF描述 |
|---|---|
| 227-1221-57 | CRIMP TOOL TWIN HEX DIE SET |
| 227-1417 | DIE SET CRIMP TWIN AX |
| 227-1420 | DIE SET N-CONNECTORS |
| 227-944 | TOOL CRIMP FRAME W/OUT DIE |
| 2277048 | BUS-BAR CURRENT TRANSFORMER 5VA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 220015-4 | 功能描述:手工工具 HHHT N SERIES RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 2200154 REV000 | 制造商:ebm-papst Inc 功能描述:EBM 3956 - Bulk |
| 220015-47-W/NIST CERT | 制造商:Biddle 功能描述: |
| 2200155 | 功能描述:接线端子工具和配件 UM-PRO 108 COVER-L BK RoHS:否 制造商:Phoenix Contact 产品:Tools & Accessories 类型:End Bracket |
| 2200156 | 功能描述:接线端子工具和配件 UM-PRO 108 COVER-R BK RoHS:否 制造商:Phoenix Contact 产品:Tools & Accessories 类型:End Bracket |
发布紧急采购，3分钟左右您将得到回复。