- 您现在的位置：买卖IC网 > Datasheet目录595 > 220015-3 (TE Connectivity)TOOL HAND CRIMP HEAVY HEAD Datasheet资料下载
参数资料
| 型号： | 220015-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMP HEAVY HEAD |
| 标准包装： | 3 |
| 系列： | Certi-Crimp |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 同轴，RF - BNC，N，TNC |
| 特点： | 侧面插入，棘齿 |
408-2331
1. The care, amount of use, and handling of the
hand tool.
2. The presence of abnormal amounts of dust and
dirt.
3. The degree of operator skill.
4. Your own established standards.
The hand tool is inspected before being shipped;
however, TE recommends that the tool be inspected
immediately upon arrival to ensure that the tool has
not been damaged during shipment.
4.1. Daily Maintenance
1. Hand tool should be immersed (handles partially
closed) in a reliable commercial degreasing
compound to remove accumulated dirt, grease, and
foreign matter. When degreasing compound is not
available, tool may be wiped clean with a soft, lint-
free cloth. Do NOT use hard or abrasive objects that
could damage the tool.
2. Make certain that the retaining pins are in place
and that they are secured with retaining rings.
3. All pins, pivot points, and bearing surfaces should
be protected with a THIN coat of any good SAE 20
motor oil. Do not oil excessively.
4. When the tool is not in use, keep handles closed
to prevent objects from becoming lodged in the
crimping jaws. Store the tool in a clean, dry area.
4.2. Periodic Inspection
A. Lubrication
Lubricate all pins, pivot points, and bearing surfaces
with SAE 20 motor oil as follows:
Tool used in daily production - lubricate daily
Tool used daily (occasional) - lubricate weekly
Tool used weekly - lubricate monthly
Wipe excess oil from tool, particularly from crimping
area. Oil transferred from the crimping area onto
certain terminations may affect the electrical
characteristics of an application.
B. Visual Inspection
1. Close tool handles until ratchet releases. Open
tool handles completely.
C. Gaging the Crimping Chambers
This inspection requires the use of a plug gage
conforming to the dimensions provided in Figures 4
and 5. TE does not manufacture or market these
gages. To gage the crimping chamber, proceed as
follows:
Inspecting Center Contact Dies
Plug gaging of the center contact crimping dies
requires the use of two separate gages, which can be
used in all 220015-[ ] tools. One gage is used inside
the radius of the die closure; the other is used
between the indent forming sections. Refer to Figure 4
and proceed as follows:
1. Close the tool handles until crimping dies are
bottomed. Do NOT apply additional pressure, or
ratchet will release.
2. With dies bottomed, check the indent-forming
closure by using the box-type plug gage shown in
Figure 4, Detail A. Align the GO element with the
contact crimping chamber and insert the element
without using force. The GO element must pass
completely through the die closure.
3. Now align the NO-GO element and try to insert it
straight into the same crimping chamber. The NO-
GO element may start entry but must NOT pass
completely through as shown in Figure 4.
4. Continue to hold the dies bottomed and insert the
second (grooved) gage to inspect the radius of the
dies, as shown in Figure 4, Detail B. Use the same
method described in Steps 2 and 3.
5. If the die closure meets both plug gage
conditions, the dies may be considered
dimensionally correct.
Inspecting Braid and Braid Gap Crimping Dies
Figure 5 provides proper plug gage dimensions -
according to tool dash number - for both the braid and
the braid gap crimping areas. Figure 5 shows the
location of both crimping areas for inspection. Proceed
as follows:
1. Remove all traces of oil and dirt from tool
crimping areas and gages.
2. Close tool handles until dies are bottomed, but
not under pressure.
NOTE
i
This tool does not have a return spring to open the
handles.
3. Using the proper plug gage, check the braid and
the braid gap closure with dies bottomed. Hold gage
in straight alignment with the dies and carefully try
to insert, without forcing, first the GO element, and
2. Inspect head assembly for worn, cracked, or
broken jaws. If damage is evident, return the tool for
evaluation and repair. See Section 6,
REPLACEMENT AND REPAIR.
Rev C
then the NO-GO element. The GO element must
pass completely through the crimp die closure. The
gage for the braid die will butt against the braid gap
crimp die.
3 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 227-1221-57 | CRIMP TOOL TWIN HEX DIE SET |
| 227-1417 | DIE SET CRIMP TWIN AX |
| 227-1420 | DIE SET N-CONNECTORS |
| 227-944 | TOOL CRIMP FRAME W/OUT DIE |
| 2277048 | BUS-BAR CURRENT TRANSFORMER 5VA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 220015-4 | 功能描述:手工工具 HHHT N SERIES RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 2200154 REV000 | 制造商:ebm-papst Inc 功能描述:EBM 3956 - Bulk |
| 220015-47-W/NIST CERT | 制造商:Biddle 功能描述: |
| 2200155 | 功能描述:接线端子工具和配件 UM-PRO 108 COVER-L BK RoHS:否 制造商:Phoenix Contact 产品:Tools & Accessories 类型:End Bracket |
| 2200156 | 功能描述:接线端子工具和配件 UM-PRO 108 COVER-R BK RoHS:否 制造商:Phoenix Contact 产品:Tools & Accessories 类型:End Bracket |
发布紧急采购，3分钟左右您将得到回复。