参数资料
| 型号： | 24C01C-I/MS |
| 厂商： | Microchip Technology |
| 文件页数： | 9/36页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 1KBIT 400KHZ 8MSOP |
| 产品培训模块： | I2C Serial EEPROM |
| 标准包装： | 100 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 1K (128 x 8) |
| 速度： | 400kHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
| 产品目录页面： | 1444 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
24C01C
6.0
6.1
WRITE OPERATIONS
Byte Write
After the receipt of each word, the four lower order
Address Pointer bits are internally incremented by one.
The higher order four bits of the word address remains
constant. If the master should transmit more than 16
Following the Start signal from the master, the device
code (4 bits), the Chip Select bits (3 bits), and the R/W
bit, which is a logic low, is placed onto the bus by the
master transmitter. The device will acknowledge this
control byte during the ninth clock pulse. The next byte
transmitted by the master is the word address and will
bytes prior to generating the Stop condition, the
address counter will roll over and the previously
received data will be overwritten. As with the byte write
operation, once the Stop condition is received an
internal write cycle will begin ( Figure 6-2 ).
be written into the Address Pointer of the 24C01C.
After receiving another Acknowledge signal from the
24C01C the master device will transmit the data word
to be written into the addressed memory location. The
24C01C acknowledges again and the master gener-
ates a Stop condition. This initiates the internal write
cycle, and during this time the 24C01C will not
generate Acknowledge signals ( Figure 6-1 ).
Note:
Page write operations are limited to writ-
ing bytes within a single physical page,
regardless of the number of bytes actu-
ally being written. Physical page boundar-
ies start at addresses that are integer
multiples of the page buffer size (or ‘page
size’) and end at addresses that are
integer multiples of [page size – 1]. If a
6.2
Page Write
Page Write command attempts to write
across a physical page boundary, the
The write control byte, word address and the first data
byte are transmitted to the 24C01C in the same way as
in a byte write. But instead of generating a Stop
condition, the master transmits up to 15 additional data
bytes to the 24C01C which are temporarily stored in
the on-chip page buffer and will be written into the
memory after the master has transmitted a Stop
condition.
result is that the data wraps around to the
beginning of the current page (overwriting
data previously stored there), instead of
being written to the next page as might be
expected. It is therefore necessary for the
application software to prevent page write
operations that would attempt to cross a
page boundary.
FIGURE 6-1:
BYTE WRITE
Bus Activity
Master
S
T
A
R
T
Control
Byte
Word
Address
Data
S
T
O
P
SDA Line
S
P
Bus Activity
FIGURE 6-2:
PAGE WRITE
A
C
K
A
C
K
A
C
K
Bus Activity
Master
S
T
A
R
T
Control
Byte
Word
Address (n)
Data n
Data n +1
Data n + 15
S
T
O
P
SDA Line
S
P
Bus Activity
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
? 1997-2012 Microchip Technology Inc.
DS21201K-page 9
相关PDF资料 |
PDF描述 |
|---|---|
| 93LC66A-I/ST | IC EEPROM 4KBIT 2MHZ 8TSSOP |
| 24LC16B-I/P | IC EEPROM 16KBIT 400KHZ 8DIP |
| 93LC66B-I/MS | IC EEPROM 4KBIT 2MHZ 8MSOP |
| 24C02C-I/ST | IC EEPROM 2KBIT 400KHZ 8TSSOP |
| 24LC16B/P | IC EEPROM 16KBIT 400KHZ 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 24C01C-IP | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:1K 5.0V I 2 C ⑩ Serial EEPROM |
| 24C01C-ISN | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:1K 5.0V I 2 C ⑩ Serial EEPROM |
| 24C01C-IST | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:1K 5.0V I 2 C ⑩ Serial EEPROM |
| 24C01CP | 制造商:Microchip Technology Inc 功能描述: |
| 24C01C-P | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:1K 5.0V I 2 C ⑩ Serial EEPROM |
发布紧急采购，3分钟左右您将得到回复。