- 您现在的位置：买卖IC网 > PDF目录22314 > 2539-SC/UPC (3M)SPLICE FIBRLOK II W/SC-UPC PIGTL PDF资料下载
参数资料
| 型号： | 2539-SC/UPC |
| 厂商： | 3M |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | SPLICE FIBRLOK II W/SC-UPC PIGTL |
| 标准包装： | 12 |
| 系列： | Fibrlok™ II |
| 类型： | 接线头 |
| 技术规格： | 0.25mm ~ 0.90mm 直径线缆，38.1mm 长 |
| 特点： | SC/UPC 包括引出线 |
| 其它名称： | 0-00-51115-22861-2 00051115228612 2539SC/UPC 5111522861 51115228612 80-6113-2240-7 80611322407 |
Note: Cleavers must be in good operating condition and used per the manufacturer’s instructions. They
should provide consistent cleave-to-coating lengths within +/- 0.5mm. Acceptable cleavers will produce
cleaved ends within 0.5° of perpendicular (typical always <1 °), free from major defects.
5.5 Cleave lengths can be confirmed on the 12.5mm length
gauge. Cleave should be within the window.
6.0 3M Fibrlok II Splice/Holder Pigtail Assembly
2539 SC/APC and 2539 SC/UPC
6.1 Cut off rubber band, position actuation lever over splice, and
lift both buffer clamps to the “up”position.
6.2 Confirm that buffer on pigtail is fully inserted inside
splice and follow steps 7.2 through 7.9.
7.0 Splice/Holder Assembly 2539
Note: Always insert the fiber first on the right (actuation lever
side) of the splice/holder.
7.1 Holding the fiber approximately ? inch (13mm) from the
bare glass, insert cleaved fiber into the guide on the right
(actuation lever side) of the splice/holder until it stops inside
the Fibrlok II splice.
Note: Push fiber straight into the fiber alignment guide, not at
an angle. Bare glass should not be visible outside of the splice. If
bare glass is visible, pull back slightly on the fiber and continue
insertion until resistance is met. Do not fully remove fibers from
splice after initial insertion.
7.2 Carefully mark the buffer at the right edge of the base.
7.3 Prepare second fiber (strip, clean and cleave) as described in
section 5.
7.4 Holding the fiber approximately ? inch (13mm) from the
bare glass, insert second fiber into the guide on the left side
(opposite actuation lever) of the splice/holder until it stops
inside the Fibrlok II splice.
7.5 While sliding the second fiber into the splice, the mark on the
first fiber should move outwards 1/8 inch (3mm) showing the
fiber ends are in contact. If this is not observed, one or both
fibers has a bad/short cleave. Remove one fiber and re-strip,
clean, re-cleave and insert back into the splice. If contact is
still not correct, repeat procedure for second fiber.
Note: To prevent contamination, never fully remove and re-
insert a cleaved end back into a splice without first re-stripping
and re-cleaving.
7.6 Center both fiber cleaves by repositioning the mark on the first
fiber half way back to its original position.
7.7 Once the fibers are centered, fully close the right buffer clamp.
You will hear an audible snap.
相关PDF资料 |
PDF描述 |
|---|---|
| ECS-H1DC475R | CAP TANT 4.7UF 20V 20% 2312 |
| MIC5891YWM | IC DRVR LATCH 8BIT SER IN 16SOIC |
| ECS-F1CE105K | CAP TANT 1UF 16V 20% RADIAL |
| HIP6019BCB | IC REG QD BCK/LINEAR 28-SOIC |
| HIP6018BCB-T | IC REG TRPL BCK/LINEAR 24-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 253-A | 功能描述:罩类、盒类及壳类产品 5.63 x 3.25 x 2.55 Almond RoHS:否 制造商:Bud Industries 产品:Boxes 外部深度:6.35 mm 外部宽度:6.35 mm 外部高度:2.56 mm NEMA 额定值: IP 等级: 材料:Acrylonitrile Butadiene Styrene (ABS) 颜色:Red |
| 253A103A45NA | 制造商:CTS 制造商全称:CTS Corporation 功能描述:Two Axis, Ministick Controller With Optional Momentary Switch |
| 253A103A45NB | 制造商:CTS 制造商全称:CTS Corporation 功能描述:Two Axis, Ministick Controller With Optional Momentary Switch |
| 253A103A50NA | 制造商:CTS 制造商全称:CTS Corporation 功能描述:Two Axis, Ministick Controller With Optional Momentary Switch |
| 253A103A50NB | 制造商:CTS 制造商全称:CTS Corporation 功能描述:Two Axis, Ministick Controller With Optional Momentary Switch |
发布紧急采购，3分钟左右您将得到回复。