- 您现在的位置：买卖IC网 > Datasheet目录596 > 2559-C (3M)SPLICE KIT W/CLEAVER FIBRLOK II Datasheet资料下载
参数资料
| 型号： | 2559-C |
| 厂商： | 3M |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | SPLICE KIT W/CLEAVER FIBRLOK II |
| 标准包装： | 1 |
| 系列： | Fibrlok™ |
| 类型： | 接线头 |
| 其它名称： | 0-00-51115-30000-4 00051115258015 00051115300004 2559C 5111530000 51115300004 80-6113-2376-9 80611323769 |
Note: Cleavers must be in good operating condition and used per the manufacturer’s instructions. They
should provide consistent cleave-to-coating lengths within +/- 0.5mm. Acceptable cleavers will produce
cleaved ends within 0.5° of perpendicular (typical always <1 °), free from major defects.
5.5 Cleave lengths can be confirmed on the 12.5mm length
gauge. Cleave should be within the window.
6.0 3M Fibrlok II Splice/Holder Pigtail Assembly
2539 SC/APC and 2539 SC/UPC
6.1 Cut off rubber band, position actuation lever over splice, and
lift both buffer clamps to the “up”position.
6.2 Confirm that buffer on pigtail is fully inserted inside
splice and follow steps 7.2 through 7.9.
7.0 Splice/Holder Assembly 2539
Note: Always insert the fiber first on the right (actuation lever
side) of the splice/holder.
7.1 Holding the fiber approximately ? inch (13mm) from the
bare glass, insert cleaved fiber into the guide on the right
(actuation lever side) of the splice/holder until it stops inside
the Fibrlok II splice.
Note: Push fiber straight into the fiber alignment guide, not at
an angle. Bare glass should not be visible outside of the splice. If
bare glass is visible, pull back slightly on the fiber and continue
insertion until resistance is met. Do not fully remove fibers from
splice after initial insertion.
7.2 Carefully mark the buffer at the right edge of the base.
7.3 Prepare second fiber (strip, clean and cleave) as described in
section 5.
7.4 Holding the fiber approximately ? inch (13mm) from the
bare glass, insert second fiber into the guide on the left side
(opposite actuation lever) of the splice/holder until it stops
inside the Fibrlok II splice.
7.5 While sliding the second fiber into the splice, the mark on the
first fiber should move outwards 1/8 inch (3mm) showing the
fiber ends are in contact. If this is not observed, one or both
fibers has a bad/short cleave. Remove one fiber and re-strip,
clean, re-cleave and insert back into the splice. If contact is
still not correct, repeat procedure for second fiber.
Note: To prevent contamination, never fully remove and re-
insert a cleaved end back into a splice without first re-stripping
and re-cleaving.
7.6 Center both fiber cleaves by repositioning the mark on the first
fiber half way back to its original position.
7.7 Once the fibers are centered, fully close the right buffer clamp.
You will hear an audible snap.
相关PDF资料 |
PDF描述 |
|---|---|
| 26852302 | CONTROL ACCESS CURRENT TRNSFRMR |
| 2814359 | CURRENT MEASURING TRANSDUCER |
| 2990010-01 | TOOL DIE&NEST FOR 2990009-01 |
| 3020-01099-0 | SHUNT CURRENT DC 100A/50MV |
| 305183-8 | TOOL EXTRACTION FOR MINI CONTACT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 2559-C | 制造商:3M Electronic Products Division 功能描述:FIBRE OPTIC SPLICE KIT |
| 2559F(H) | 制造商:JT&T Products 功能描述: |
| 2559HQPMD2412PMB2A2GNI55 | 制造商:SUNON 功能描述:- Bulk |
| 255ABX105-125D | 制造商:Struthers-Dunn 功能描述: |
| 255ABX119 | 制造商:Struthers-Dunn 功能描述: |
发布紧急采购，3分钟左右您将得到回复。