- 您现在的位置：买卖IC网 > Datasheet目录596 > 2559-C (3M)SPLICE KIT W/CLEAVER FIBRLOK II Datasheet资料下载
参数资料
| 型号： | 2559-C |
| 厂商： | 3M |
| 文件页数： | 4/4页 |
| 文件大小： | 0K |
| 描述： | SPLICE KIT W/CLEAVER FIBRLOK II |
| 标准包装： | 1 |
| 系列： | Fibrlok™ |
| 类型： | 接线头 |
| 其它名称： | 0-00-51115-30000-4 00051115258015 00051115300004 2559C 5111530000 51115300004 80-6113-2376-9 80611323769 |
7.8 Grasp the left fiber about 2 inches from the holder and push the
fiber in until it bows about 1/8 to 1/4 inch (3mm to 6mm). Push
down on the actuation lever until the Fibrlok II Splice is actuated.
An audible click can be heard and you should feel the splice cap
snap down into place when completely closed. The cap should be
level with the Fibrlok splice top surface.
7.9 Release the bow in the fiber and fully close the left buffer clamp.
Again, you will hear an audible snap.
8.0 Fiber Repositioning
8.1 If high loss is observed after the splice has been actuated, it is possible that the fiber ends are separated.
In this case, lift the splice cap and reposition the fiber ends, as instructed below.
8.2 While the splice is still in the holder assembly, lift the actuation
lever and insert the cap removal tool over the splice cap. Grasp
both sides of the splice holder base and lift the cap up and off the
splice while gently rocking lengthwise. Replace the cap parallel
to the top, but raised about 1mm (0.04 inch) as it snaps into
place.
8.3 Carefully reposition fiber. Refer to section 7.0 for proper
fiber centering and splice actuation.
8.4 Place splice cap back on the Fibrlok splice and push down the
actuation lever until cap has been fully actuated.
8.5 If after two attempts, an acceptable splice loss is not obtained,
remove fibers and replace the Fibrlok splice with a new splice.
Redo fiber preparation (section 5) by re-stripping, cleaning, and
cleaving both fibers. Then repeat steps in section 7.
8.6 Upon completion, the actuation lever can be removed and
discarded if desired.
Rev B
相关PDF资料 |
PDF描述 |
|---|---|
| 26852302 | CONTROL ACCESS CURRENT TRNSFRMR |
| 2814359 | CURRENT MEASURING TRANSDUCER |
| 2990010-01 | TOOL DIE&NEST FOR 2990009-01 |
| 3020-01099-0 | SHUNT CURRENT DC 100A/50MV |
| 305183-8 | TOOL EXTRACTION FOR MINI CONTACT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 2559-C | 制造商:3M Electronic Products Division 功能描述:FIBRE OPTIC SPLICE KIT |
| 2559F(H) | 制造商:JT&T Products 功能描述: |
| 2559HQPMD2412PMB2A2GNI55 | 制造商:SUNON 功能描述:- Bulk |
| 255ABX105-125D | 制造商:Struthers-Dunn 功能描述: |
| 255ABX119 | 制造商:Struthers-Dunn 功能描述: |
发布紧急采购，3分钟左右您将得到回复。