- 您现在的位置：买卖IC网 > PDF目录298290 > 25LC040A-E/ST 512 X 8 SPI BUS SERIAL EEPROM, PDSO8 PDF资料下载
参数资料
| 型号： | 25LC040A-E/ST |
| 元件分类： | PROM |
| 英文描述： | 512 X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| 封装： | 4.40 MM, ROHS COMPLIANT, PLASTIC, TSSOP-8 |
| 文件页数： | 5/30页 |
| 文件大小： | 452K |
| 代理商： | 25LC040A-E/ST |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
2009 Microchip Technology Inc.
DS21827F-page 13
25AA040A/25LC040A
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
PIN FUNCTION TABLE
3.1
Chip Select (CS)
A low level on this pin selects the device. A high level
deselects the device and forces it into Standby mode.
However, a programming cycle which is already
initiated or in progress will be completed, regardless of
the CS input signal. If CS is brought high during a
program cycle, the device will go into Standby mode as
soon as the programming cycle is complete. When the
device is deselected, SO goes to the high-impedance
state, allowing multiple parts to share the same SPI
bus. A low-to-high transition on CS after a valid write
sequence initiates an internal write cycle. After power-
up, a low level on CS is required prior to any sequence
being initiated.
3.2
Serial Output (SO)
The SO pin is used to transfer data out of the
25XX040A. During a read cycle, data is shifted out on
this pin after the falling edge of the serial clock.
3.3
Write-Protect (WP)
The WP pin is a hardware write-protect input pin.
When it is low, all writes to the array or STATUS
registers are disabled, but any other operations
function normally. When WP is high, all functions,
including nonvolatile writes, operate normally. At any
time, when WP is low, the write enable reset latch will
be reset and programming will be inhibited. However,
if a write cycle is already in progress, WP going low will
not change or disable the write cycle. See Table 2-4 for
the Write-Protect Functionality Matrix.
3.4
Serial Input (SI)
The SI pin is used to transfer data into the device. It
receives instructions, addresses and data. Data is
latched on the rising edge of the serial clock.
3.5
Serial Clock (SCK)
The SCK is used to synchronize the communication
between a master and the 25XX040A. Instructions,
addresses or data present on the SI pin are latched on
the rising edge of the clock input, while data on the SO
pin is updated after the falling edge of the clock input.
3.6
Hold (HOLD)
The HOLD pin is used to suspend transmission to the
25XX040A while in the middle of a serial sequence
without having to retransmit the entire sequence again.
It must be held high any time this function is not being
used. Once the device is selected and a serial
sequence is underway, the HOLD pin may be pulled
low to pause further serial communication without
resetting the serial sequence. The HOLD pin must be
brought low while SCK is low, otherwise the HOLD
function will not be invoked until the next SCK high-to-
low transition. The 25XX040A must remain selected
during this sequence. The SI, SCK and SO pins are in
a high-impedance state during the time the device is
paused and transitions on these pins will be ignored. To
resume serial communication, HOLD must be brought
high while the SCK pin is low, otherwise serial
communication will not resume. Lowering the HOLD
line at any time will tri-state the SO line.
Name
PDIP,
SOIC,
MSOP,
TSSOP,
DFN
Rotated
TSSOP
SOT-23
Function
CS
1
3
5
Chip Select Input
SO
2
4
Serial Data Output
WP
3
5
—
Write-Protect Pin
VSS
4
6
2
Ground
SI
5
7
3
Serial Data Input
SCK
6
8
1
Serial Clock Input
HOLD
7
1
—
Hold Input
VCC
8
2
6
Supply Voltage
相关PDF资料 |
PDF描述 |
|---|---|
| 25LR45-Q | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| 25LR10-Q | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| 25LB22-Q-Z | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| 25LR22-H-Z | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| 25LR30-Q-Z | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 25LC040A-H/SN | 功能描述:电可擦除可编程只读存储器 4K, 512 X 8, 2.5V SER EE 150C RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 25LC040A-I/MC | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4K SPI Bus Serial EEPROM |
| 25LC040A-I/MS | 功能描述:电可擦除可编程只读存储器 4K 512X8 2.5V SER EE IND RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 25LC040A-I/OT | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4K SPI Bus Serial EEPROM |
| 25LC040A-I/P | 功能描述:电可擦除可编程只读存储器 4K 512X8 2.5V SER EE IND RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。