- 您现在的位置：买卖IC网 > PDF目录4395 > 25LC080D-I/P (Microchip Technology)IC SRL EEPROM 1KX8 2.5V 8-PDIP PDF资料下载
参数资料
| 型号： | 25LC080D-I/P |
| 厂商： | Microchip Technology |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC SRL EEPROM 1KX8 2.5V 8-PDIP |
| 标准包装： | 60 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 8K (1K x 8) |
| 速度： | 5MHz，10MHz |
| 接口： | SPI 3 线串行 |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 产品目录页面： | 1448 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
25XX080C/D
3.0
PIN DESCRIPTIONS
grounded and still be able to write to the STATUS reg-
ister. The WP pin functions will be enabled when the
The descriptions of the pins are listed in Table 3-1.
WPEN bit is set high.
TABLE 3-1:
PIN FUNCTION TABLE
3.4
Serial Input (SI)
Name
Pin Number
Function
The SI pin is used to transfer data into the device. It
receives instructions, addresses and data. Data is
CS
SO
1
2
Chip Select Input
Serial Data Output
latched on the rising edge of the serial clock.
WP
3
Write-Protect Pin
3.5
Serial Clock (SCK)
V SS
SI
SCK
HOLD
V CC
4
5
6
7
8
Ground
Serial Data Input
Serial Clock Input
Hold Input
Supply Voltage
The SCK is used to synchronize the communication
between a master and the 25XX080C/D. Instructions,
addresses or data present on the SI pin are latched on
the rising edge of the clock input, while data on the SO
pin is updated after the falling edge of the clock input.
3.6
Hold (HOLD)
3.1
Chip Select (CS)
The HOLD pin is used to suspend transmission to the
A low level on this pin selects the device. A high level
deselects the device and forces it into Standby mode.
However, a programming cycle which is already
initiated or in progress will be completed, regardless of
the CS input signal. If CS is brought high during a
program cycle, the device will go into Standby mode as
soon as the programming cycle is complete. When the
device is deselected, SO goes to the high-impedance
state, allowing multiple parts to share the same SPI
bus. A low-to-high transition on CS after a valid write
sequence initiates an internal write cycle. After power-
up, a low level on CS is required prior to any sequence
being initiated.
25XX080C/D while in the middle of a serial sequence
without having to retransmit the entire sequence again.
It must be held high any time this function is not being
used. Once the device is selected and a serial
sequence is underway, the HOLD pin may be pulled
low to pause further serial communication without
resetting the serial sequence. The HOLD pin must be
brought low while SCK is low, otherwise the HOLD
function will not be invoked until the next SCK high-to-
low transition. The 25XX080C/D must remain selected
during this sequence. The SI, SCK and SO pins are in
a high-impedance state during the time the device is
paused and transitions on these pins will be ignored. To
resume serial communication, HOLD must be brought
3.2
Serial Output (SO)
high while the SCK pin is low, otherwise serial
communication will not resume. Lowering the HOLD
The SO pin is used to transfer data out of the
25XX080C/D. During a read cycle, data is shifted out
on this pin after the falling edge of the serial clock.
line at any time will tri-state the SO line.
3.3
Write-Protect (WP)
This pin is used in conjunction with the WPEN bit in the
STATUS register to prohibit writes to the nonvolatile
bits in the STATUS register. When WP is low and
WPEN is high, writing to the nonvolatile bits in the STA-
TUS register is disabled. All other operations function
normally. When WP is high, all functions, including
writes to the nonvolatile bits in the STATUS register
operate normally. If the WPEN bit is set, WP low during
a STATUS register write sequence will disable writing
to the STATUS register. If an internal write cycle has
already begun, WP going low will have no effect on the
write.
The WP pin function is blocked when the WPEN bit in
the STATUS register is low. This allows the user to
install the 25XX080C/D in a system with WP pin
? 2009 Microchip Technology Inc.
DS22151A-page 13
相关PDF资料 |
PDF描述 |
|---|---|
| 25LC040/P | IC EEPROM 4KBIT 2MHZ 8DIP |
| RMA49DTMI | CONN EDGECARD 98POS R/A .125 SLD |
| M24308/2-286 | CONN D-SUB RCPT HD 15P SER 90 |
| 25C040-I/P | IC EEPROM 4KBIT 3MHZ 8DIP |
| 25AA080A-I/SN | IC EEPROM 8KBIT 10MHZ 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 25LC080DT-E/MNY | 功能描述:电可擦除可编程只读存储器 8K 1K X 8 32B PAGE 2.5V SER EE EXT RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 25LC080DT-E/MS | 功能描述:电可擦除可编程只读存储器 8K 1K X 8 32B PAGE 2.5V SER EE EXT RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 25LC080DT-E/P | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8K SPI Bus Serial EEPROM |
| 25LC080DT-E/SN | 功能描述:电可擦除可编程只读存储器 8K 1K X 8 32B PAGE 2.5V SER EE EXT RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| 25LC080DT-E/ST | 功能描述:电可擦除可编程只读存储器 8K 1K X 8 32B PAGE 2.5V SER EE EXT RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。