- 您现在的位置：买卖IC网 > PDF目录33403 > 2SC4553 7.5 A, 100 V, NPN, Si, POWER TRANSISTOR PDF资料下载
参数资料
| 型号： | 2SC4553 |
| 元件分类： | 功率晶体管 |
| 英文描述： | 7.5 A, 100 V, NPN, Si, POWER TRANSISTOR |
| 封装： | PLASTIC PACKAGE-3 |
| 文件页数： | 6/8页 |
| 文件大小： | 243K |
| 代理商： | 2SC4553 |
Design Documentation (See the application circuit diagrams)
1. Power-supply voltage (VIN pin)
The resistor R1 (when VCC = 12 V R1 = 330 Ω, and when VCC = 24 R1 = about 1.2 kΩ) is inserted between VIN and
the power supply VCC pin. When the ICC current is set in the range 6 to 50 mA, the VIN pin will be regulated to be
6.7 V. Not only does this provide stability with respect to power-supply voltage variations and motor kickback, but it
also provides adequate strength to withstand surges.
2. Output transistors (OUT1 and OUT2 pins)
A Zener diodes with the following characteristics is inserted between the collector and base of each output transistor
to absorb kickback voltages at 57 V (typical) and provide output protection.
Sustained output voltage : VO = 65 V minimum (design guarantee)
Output current
: IO = 1.5 A maximum
Output saturation voltage : VO sat = 1.25 V/1.0 A (typical)
Safe operating range
: IO = 1.0 A, VOLM = 57 V, t = 200 μs
3. Output circuit kickback voltage protection (Z1 and Z2 pins)
These ICs support output protection that minimizes kickback noise by changing the kickback absorption voltage and
absorption method according to the output current and power-supply voltage used.
— When the Z1 and Z2 pins are shorted
The output protection voltage will be 32 V (typical) using a VCC = 12 V power supply.
— When the Z1 and Z2 pins are open
The output protection voltage will be 57 V (typical) using a VCC = 24 V power supply.
— With a Zener diode inserted between Z1 and VCC or between Z1 and ground
This technique handles 120 mm H speed applications which require large output currents and involve large
amounts of heat generated in the IC by dissipating the motor coil switching loss in external Zener diodes.
4. Output protection when the motor is lock (C, RD, and FG pins)
This circuit detects motor stopping due to, for example, overloading, and cuts the coil current. It also automatically
recovers drive and motor turning from the output stopped state when the load returns to an appropriate level. The lock
detection time is set with the value of an external capacitor.
When C = 0.47 μF
Lock detection time: about 1 second
Lock protection time (output on): about 0.5 second
(output off): about 3 seconds
The RD pin (LB1668) is an open collector output and outputs a low level during drive and a high level when stopped.
The FG pin (LB1667) is an open collector output and is switched between high and low by the drive phase. It goes to
the high level when the motor is stopped.
5. Thermal shutdown
This circuit turns the output off in response to coil shorting or IC overheating.
6. In applications that use an external transistor to turn the cooling fan power on and off, connect a capacitor of about
0.47 to 10 μF between the fan power supply VCC and ground to provide a regenerative route for the fan motor coil
current.
No. 4944-6/8
LB1668, LB1668M, LB1667, LB1667M
相关PDF资料 |
PDF描述 |
|---|---|
| 2SC4554-AZ | 15 A, 100 V, NPN, Si, POWER TRANSISTOR |
| 2SC4564C | 0.3 A, 200 V, NPN, Si, POWER TRANSISTOR |
| 2SA1749E | 0.3 A, 200 V, PNP, Si, POWER TRANSISTOR |
| 2SC4568-GB | UHF BAND, Si, NPN, RF SMALL SIGNAL TRANSISTOR |
| 2SC4568-T74 | UHF BAND, Si, NPN, RF SMALL SIGNAL TRANSISTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 2SC4553-AZ | 制造商:Renesas Electronics Corporation 功能描述:NPN PWR Transistor,100V,7.5A,isoTO-220 |
| 2SC4553-AZ-K | 制造商:Renesas Electronics 功能描述:NPN Bulk |
| 2SC4554-AZ | 制造商:Renesas Electronics 功能描述:Cut Tape 制造商:Renesas Electronics Corporation 功能描述:NPN PWR Transistor,100V,15A,isoTO-220 制造商:Renesas 功能描述:Trans Digital BJT NPN 100V 15A 3-Pin(3+Tab) MP-45F |
| 2SC4554-AZ-K | 制造商:Renesas Electronics 功能描述:Bulk |
| 2SC4554-K(AZ) | 制造商:Renesas Electronics Corporation 功能描述:Bulk |
发布紧急采购，3分钟左右您将得到回复。