- 您现在的位置：买卖IC网 > PDF目录18619 > 311386-3 (TE Connectivity)90DEG BEND SEGMENT RG-405/U PDF资料下载
参数资料
| 型号： | 311386-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | 90DEG BEND SEGMENT RG-405/U |
| 标准包装： | 1 |
| 系列： | * |
408-6788
9.1. Daily Maintenance
1. Remove dust, moisture, and other contaminants
Suggested Plug Gage Design
from the tool with a clean brush or a soft, lint-free
cloth. Do NOT use objects that could damage the
tool.
2. Make sure that the proper retaining pins are in
place and are secured with the proper retaining
GO
6.35 ±0.25 [.25 ±.01]
NO-GO
rings.
3. Make certain that all pins, pivot points, and
bearing surfaces are protected with a THIN coat of
any good SAE 20 motor oil. Do NOT oil excessively.
4. When the tool is not in use, keep the handles
closed to prevent objects from becoming lodged in
12.7 [.50]
63.5 [2.5] (Typ)
GAGE ELEMENT DIAMETERS
GO NO-GO
12.7 [.50]
the crimping chambers and store the tool in a clean,
dry area.
15.915-15.920 [.6266-.6268]
16.078-16.083 [.6330-.6332]
9.2. Periodic Inspection
Inspection of Crimping Chamber
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the tool and/or be supplied to
supervisory personnel responsible for the tool. Though
recommendations call for at least one inspection per
Crimping Chamber
16.0 ±0.08
[.630 ±.003]
Top of Ram
Die Inserts
312253-1
(Required)
month, the inspection frequency should be based on
the amount of use, working conditions, operator
training and skill, and established company standards.
These inspections should be performed in the
following sequence:
A. Visual Inspection
1. Remove all lubrication and accumulated film by
immersing the tool (handles partially closed) in a
suitable commercial degreaser that will not affect
paint or plastic material.
GO/NO-GO
Gage
GO Element
NO-GO Element
Stop
Surface
2. Make certain that all retaining pins are in place
and are secured with retaining rings. If
replacements are necessary, refer to Section 10,
REPLACEMENT AND REPAIR.
Crimping
Chamber
12.2 ±0.25
[.48 ±.010]
Crimping
Chamber
3. Inspect crimping chambers for pitted or chipped
surfaces.
4. Close the tool handles until the ratchet releases,
then allow handles to open freely. If they do not
open quickly and fully, the spring is defective and
must be replaced. Refer to Section 10,
REPLACEMENT AND REPAIR.
GO element must
pass completely
through the
crimping chamber.
NO-GO element may
enter partially, but must
not pass completely
through the crimping
chamber.
B. Gaging the Crimping Chambers
This inspection requires the use of a plug gage
conforming to the dimensions listed in Figure 17. TE
does not manufacture or market these gages. To gage
the crimping chambers, proceed as follows:
1. Insert Die Set 312253-1 as described in
Section 5, TOOL SETUP. Do NOT insert the locator.
2. Close the tool handles until the ram touches the
stop surfaces. Refer to Figure 17.
Rev L
Figure 17
3. Align the GO element of the gage with the
crimping chamber so that the top and bottom of the
gage align with the surfaces of the die inserts and
ram.
4. Push the element straight into the crimping
chamber without using force. The GO element must
pass completely through the crimping chamber as
shown in Figure 17.
10 of 12
相关PDF资料 |
PDF描述 |
|---|---|
| 476P6P144 | CABLE STR MALE-MALE 6POS 12' |
| 1912P36 | CABLE SGL-END STR MALE 12POS 3' |
| GP1UM277XK | RECEIVER REMOTE CTRL TOP 56.8KHZ |
| GP1UM262XK0F | RECEIVER REMOTE CTRL TOP 36.7KHZ |
| 553P3S36 | CBL STR MALE-R/A FEMALE 3POS 3' |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 311392-1 | 制造商:TE Connectivity 功能描述:90 DEGREE BEND TOOL BODY ASSY - Bulk |
| 311395-1 | 功能描述:手工工具 CUT-OFF FIXTURE RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 311396-1 | 功能描述:手工工具 CABLE DRESSING FIXTURE RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 31-1397 | 制造商:TDK-EPC 功能描述:4 drum spill pallet ramp |
| 31-1398 | 制造商:TDK-EPC 功能描述:2 drum spill pallet ramp |
发布紧急采购，3分钟左右您将得到回复。