- 您现在的位置：买卖IC网 > PDF目录18619 > 311386-3 (TE Connectivity)90DEG BEND SEGMENT RG-405/U PDF资料下载
参数资料
| 型号： | 311386-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 5/12页 |
| 文件大小： | 0K |
| 描述： | 90DEG BEND SEGMENT RG-405/U |
| 标准包装： | 1 |
| 系列： | * |
408-6788
Using Cable Dressing Fixture
2. Push lightly against the cable while slowly
rotating the trimmer tool clockwise several times.
Insert Cable into Hole
and Saw Through
Jacket While Rotating
Cable
Detail A
Slot for
Saw Blade
Cable
3. Remove the trimmer tool and clean any chips
from the cable end.
4. Re-insert the cable into the cable dressing fixture
for pointing. Refer to Figure 5, Detail B. Keep
pressure against the fixture and rotate the cable
slowly while filing on the 45° surface with a small
pillar file or mill file. Continue filing until the
conductor offers no resistance to the file.
i NOTE A final inspection must be performed to ensure that no
!
!
i NOTE Before crimping, insert the prepared cable into the
Vise
Detail B
Rotate Cable Slowly
While Filing Across This
Surface to Form 45° Tip
on End of Conductor
Figure 5
4. Remove the cable from the fixture. Using a razor
blade, carefully cut and remove the dielectric to
expose the center conductor.
CAUTION
DO NOT nick or score the center conductor.
To smooth the copper shield and dielectric, proceed as
follows:
1. Slip the correct end of the trimmer tool over the
exposed cable end. See Figure 6.
Using Trimmer Tool
Holes
After Slipping Trimmer Over
Cable, Rotate Trimmer (As
Shown) 2 or 3 Revolutions to
Smooth Copper Shield and
Dielectric
5. Remove the cable and brush off any chips.
NOTE
metal chips or burrs are present on the cable dielectric
surface or on the cable shield inner or outer surfaces.
5. TOOL SETUP (Figure 7)
Before prepared cable can be crimped to a connector,
the hand crimping tool must be set up with the
appropriate locator and die set. Proceed as follows:
1. Select the proper hand tool locator from Figure 2.
2. Loosen the locator locking screw, insert the
locator into the tool head cavity, making sure that
the locator is bottomed in the cavity, then re-tighten
the locking screw. Refer to Figure 7, Detail A.
3. Select the proper die set for either RG-402 or
RG-405 cable. Position each die on the respective
tool jaw and make sure that the chamfer is oriented
as shown in Figure 7, Detail A.
CAUTION
An unacceptable crimp will result if the die chamfers are
not positioned as shown.
4. Fasten the dies to the jaws with the screws, but
do not tighten the screws until the dies are aligned.
5. To align the dies, place the cable inside the
locator and squeeze the tool handles to close the
tool. Check for even alignment of the dies, as
shown in Figure 7, Detail B, then tighten the screws
to secure the dies.
6. CRIMPING PROCEDURE
NOTE
BACK of the connector assembly until the cable bottoms
on the shoulder of the connector assembly.
6.1. For Connectors with Fixed Collars
(Except Right Angle Connectors)
Figures 8 and 9 show typical plug and panel jack
connectors with fixed collars.
Rev L
Cable
Figure 6
Cable Size
Designations
Proceed as follows:
1. Carefully insert the cable into the connector until
the cable bottoms on the shoulder of the connector.
5 of 12
相关PDF资料 |
PDF描述 |
|---|---|
| 476P6P144 | CABLE STR MALE-MALE 6POS 12' |
| 1912P36 | CABLE SGL-END STR MALE 12POS 3' |
| GP1UM277XK | RECEIVER REMOTE CTRL TOP 56.8KHZ |
| GP1UM262XK0F | RECEIVER REMOTE CTRL TOP 36.7KHZ |
| 553P3S36 | CBL STR MALE-R/A FEMALE 3POS 3' |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 311392-1 | 制造商:TE Connectivity 功能描述:90 DEGREE BEND TOOL BODY ASSY - Bulk |
| 311395-1 | 功能描述:手工工具 CUT-OFF FIXTURE RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 311396-1 | 功能描述:手工工具 CABLE DRESSING FIXTURE RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 31-1397 | 制造商:TDK-EPC 功能描述:4 drum spill pallet ramp |
| 31-1398 | 制造商:TDK-EPC 功能描述:2 drum spill pallet ramp |
发布紧急采购，3分钟左右您将得到回复。