- 您现在的位置：买卖IC网 > PDF目录21897 > 4306-52 (Peregrine Semiconductor)IC DSA 5BIT 50 OHM 20-QFN PDF资料下载
参数资料
| 型号： | 4306-52 |
| 厂商： | Peregrine Semiconductor |
| 文件页数： | 6/11页 |
| 文件大小： | 0K |
| 描述： | IC DSA 5BIT 50 OHM 20-QFN |
| 标准包装： | 1 |
| 系列： | UltraCMOS™ |
| 衰减值： | 31dB |
| 容差： | ±0.3dB |
| 频率范围： | 0 ~ 4GHz |
| 阻抗： | 50 欧姆 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 其它名称： | 1046-1033-6 |
PE4306
Product Specification
Programming Options
Parallel/Serial Selection
Either a parallel or serial interface can be used to
control the PE4306. The P/S bit provides this
selection, with P/S = LOW selecting the parallel
interface and P/S = HIGH selecting the serial
interface.
Parallel / Direct Mode Interface
The parallel interface consists of five CMOS-
compatible control lines that select the desired
attenuation state, as shown in Table 5 .
The parallel interface timing requirements are
defined by Figure 18 (Parallel Interface Timing
Diagram), Table 9 (Parallel Interface AC
Characteristics), and switching speed ( Table 1 ).
For parallel programming the Latch Enable (LE)
should be held LOW while changing attenuation
state control values, then pulse LE HIGH to LOW
(per Figure 18 ) to latch new attenuation state into
device.
For direct programming, the Latch Enable (LE) line
should be pulled HIGH. Changing attenuation state
control values will change device state to new
attenuation. Direct Mode is ideal for manual control
of the device (using hardwire, switches, or jumpers).
Table 5. Truth Table
The LE input controls the latch. When LE is HIGH,
the latch is transparent and the contents of the serial
shift register control the attenuator. When LE is
brought LOW, data in the shift register is latched.
The shift register should be loaded while LE is held
LOW to prevent the attenuator value from changing
as data is entered. The LE input should then be
toggled HIGH and brought LOW again, latching the
new data. The stop bit (B0) of the data should
always be low to prevent an unknown state in the
device. The timing for this operation is defined by
Figure 17 (Serial Interface Timing Diagram) and
Table 8 (Serial Interface AC Characteristics).
Power-up Control Settings
The PE4306 always assumes a specifiable
attenuation setting on power-up. This feature exists
for both the Serial and Parallel modes of operation,
and allows a known attenuation state to be
established before an initial serial or parallel control
word is provided.
When the attenuator powers up in Serial mode
(P/S = 1), the five control bits and a stop bit are set
to whatever data is present on the five parallel data
inputs (C1 to C16). This allows any one of the 32
attenuation settings to be specified as the power-up
state.
When the attenuator powers up in Parallel mode (P/
S = 0) with LE = 0, the control bits are automatically
P/S
0
0
0
0
0
C16
0
0
0
0
0
C8
0
0
0
0
1
C4
0
0
0
1
0
C2
0
0
1
0
0
C1
0
1
0
0
0
Attenuation State
Reference Loss
1 dB
2 dB
4 dB
8 dB
set to one of four possible values. These four values
are selected by the two power-up control bits, PUP1
and PUP2, as shown in Table 6 (Power-Up Truth
Table, Parallel Mode).
Table 6. Power-Up Truth Table, Parallel
Interface Mode
0
0
1
1
0
1
0
1
0
1
0
1
16 dB
31 dB
P/S
0
LE
0
PUP2
0
PUP1
0
Attenuation State
Reference Loss
Note: Not all 32 possible combinations of C1-C16 are shown
Serial Interface
The PE4306’s serial interface is a 6-bit serial-in,
0
0
0
0
0
0
0
1
1
0
1
X
0
1
1
X
8 dB
16 dB
31 dB
Defined by C1-C16
parallel-out shift register buffered by a transparent
latch. The latch is controlled by three CMOS-
compatible signals: Data, Clock, and Latch Enable
(LE). The Data and Clock inputs allow data to be
serially entered into the shift register, a process that
is independent of the state of the LE input.
?2003-2013 Peregrine Semiconductor Corp. All rights reserved.
Note: Power up with LE = 1 provides normal parallel operation with C1-C16,
and PUP1 and PUP2 are not active.
Document No. DOC-30007-2 │ UltraCMOS ? RFIC Solutions
Page 6 of 11
Peregrine products are protected under one or more of the following U.S. Patents: http://patents.psemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| DCA-20PC-5-DC4-RL-C | AMMETER LED 8-36VDC 1.999A RED |
| DK952A | DPM LED +5V 2V 3.5 DIGIT GRN |
| 4308-52 | IC DSA 5BIT 75 OHM 20-QFN |
| DK853A | DPM LED +5V 20V 3.5 DIGIT RED |
| DK852A | DPM LED +5V 2V 3.5 DIGIT RED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 430654-501 | 功能描述:热电模块 CP08,127,05,L,EP W4.5 25x25x3.1mm RoHS:否 制造商:Laird Technologies / Thermal Solutions 类型:Ceramic Plate Q最大:24 W ΔT最大:+ 63 C 最大电流:2.8 A 最大电压:14.4 V 长度:30 mm 宽度:30 mm 高度:3.2 mm |
| 430-658A | 制造商:LG Corporation 功能描述:METAL FBT SUP |
| 4306-680 | 制造商:Tusonix 功能描述:- Bulk |
| 4306-680 LF | 制造商:Tusonix 功能描述:FILTER PUSH FIT 5PF |
| 4306-680LF | 功能描述:电磁干扰直通滤波器 5pF 200Volts@125C RoHS:否 制造商:Tusonix 电容:0.027 uF 电压额定值:50 V 电路类型: 最大直流电流: 最大直流电阻: 工作温度范围:- 55 C to + 125 C 系列:4403 螺纹大小:4-40 UNC-2A |
发布紧急采购，3分钟左右您将得到回复。