- 您现在的位置：买卖IC网 > PDF目录156623 > 4610M-902-104 Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits PDF资料下载
参数资料
| 型号： | 4610M-902-104 |
| 英文描述： | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 中文描述： | KONDENSATOR NETZWERK |
| 文件页数： | 57/62页 |
| 文件大小： | 1883K |
| 代理商： | 4610M-902-104 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页当前第57页第58页第59页第60页第61页第62页
Specifications are subject to change without notice.
336
1
Solder Paste
Printing
Reflow; Convection,
IR and Vapor Phase
This application note is designed to provide step-by-step processing recommendations. It covers
the popular soldering process currently in use and provides recommendations and cautions for
each step. Since many variations of time, temperature, processes, cleaning agents and board
types in use, you will want to verify your own system. Bourns does not recommend the backside
mounting of passive components.
The process steps, recommendations and cautions are based on Bourns surveys of users, equip-
ment manufacturers and materials suppliers. No warranty expressed or implied is made in regards
to the following recommendations.
GENERAL
Use the optimum
solder paste for the pattern,
printing process, and sol-
der joint quality.
RECOMMENDED
Typical solder paste alloy is
63Sn/37Pb. RMA,No-Clean
or Halide Free Water
Soluble fluxes should be
used.
CAUTION
Since solder paste usually
contains a high percentage
of activators, you must
ensure adequate cleaning
to remove all residues.
Consult your solder paste
supplier for cleaning meth-
ods. When cleaning addi-
tives are needed, only
those that are Halide Free
should be used.
2
Adhesive
Application
GENERAL
The adhesive must hold the
unit in correct orientation
upon placement and main-
tain the correct position
during any physical han-
dling before the final sol-
dering process.
RECOMMENDED
To assure positional stabili-
ty, place a single dot of
epoxy under the unit.
CAUTION
Use sufficient adhesive to
assure stability through the
cure process.
Avoid overflow of epoxy
onto solder pads and termi-
nal areas.
Excessive curing before
placement may not allow
full seating of the part
causing incomplete solder
connections.
3
Network
Placement
GENERAL
Use pick-and-place equip-
ment with a vacuum nozzle
ID that allows adequate
suction to pick the unit out
of the pocket cavity.
RECOMMENDED
Ensure nozzle inside diam-
eter and vacuum levels are
adequate to maintain suc-
tion and part alignment.
CAUTION
Ensure parts are placed so
that all leads are centered
on the solder pads.
Align the leads with the sol-
der belt direction of travel
to avoid the part body cre-
ating a thermal shadowing
effect.
Excessive placement force
to the part should be avoid-
ed to minimize the risk of
package damage.
5
Flux
Application
Flow (Wave)
GENERAL
Use the correct flux to
remove surface oxides,
prevent re-oxidation and
promote wetting.
RECOMMENDED
RMA (Rosin Mildly
Activated) flux or Halide
Free Water Soluble flux is
recommended.
CAUTION
Avoid fluxes with Halide
activators.
4
Adhesive
Cure
GENERAL
Heat/time cure should be
accomplished using either
an infrared radiation or a
convection oven.
RECOMMENDED
Cure using the temperature
profile specified by the adhe-
sive manufacturer.
CAUTION
Use sufficient cure time to
ensure complete adhesive
transition from fluid to solid.
Care should be taken to
assure the placed units are
not exposed to temperatures
in excess of the manufactur-
er's maximum.
Do not exceed the maximum
temperature rating of the
component.
Epoxy
Soldering And Cleaning Processes
相关PDF资料 |
PDF描述 |
|---|---|
| 4610X-101-101 | WIDERSTAND NETZWERK DICKFILM 100R 5ST |
| 4610X-101-102 | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 4610X-101-103 | WIDERSTAND NETZWERK DICKFILM 10K 5ST |
| 4610X-101-104 | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 4610X-101-105 | WIDERSTAND NETZWERK DICKFILM 1M 5ST |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4610M-902104LF | 制造商:Bourns / JW Miller 功能描述:Cap Ceramic Network 0.1uF 50V X7R 20% SIP 5 Capacitor 125°C 制造商:Bourns 功能描述:Cap Ceramic Network 0.1uF 50V X7R 20% SIP 5 Capacitor 125°C |
| 4610M-902-104LF | 功能描述:电容器阵列与网络 10Pin 0.1uF 20% Isolated X7R RoHS:否 制造商:AVX 电容:0.1 uF 容差:20 % 电压额定值:6.3 V 元件数量:2 工作温度范围: 外壳长度:0.8 mm 外壳宽度:1.6 mm 外壳高度:0.5 mm 端接类型:SMD/SMT 系列:PG |
| 4610M-AP1-472LF | 制造商:Bourns Inc 功能描述: |
| 4610M-AP2-104DLF | 功能描述:电阻器网络与阵列 10Pin 2% 100K Isolated RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel |
| 4610M-LF | 制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:Networks |
发布紧急采购，3分钟左右您将得到回复。