- 您现在的位置：买卖IC网 > Datasheet目录290 > 5.05.01 FLASHER 5 (Segger Microcontroller Systems)PROGRAMMING TOOL FOR MCU Datasheet资料下载
参数资料
| 型号： | 5.05.01 FLASHER 5 |
| 厂商： | Segger Microcontroller Systems |
| 文件页数： | 1/4页 |
| 文件大小： | 0K |
| 描述： | PROGRAMMING TOOL FOR MCU |
| 标准包装： | 1 |
| 类型： | 系统内编程器 |
| 适用于相关产品： | Renesas MCUs |
| 所含物品： | 编程器 |
| 产品目录页面： | 737 (CN2011-ZH PDF) |
| 其它名称： | 899-1001 |
ASCII command interface to Flasher V2.00
Introduction
Since firmware version 1.84, Flasher 4, Flasher 4R1, Flasher 5 and Flasher ST7 support a simple
ASCII command interface via RS232.
This document describes the ASCII command interface of Flasher firmware version 2.00
Once set up using Flasher PC program, Flasher can be driven by any application or just a simple ter-
minal using ASCII commands.
Every known command is acknowledged by Flasher and then executed.
After command execution, Flasher sends an ASCII reply message.
If an unknown command is received, Flasher responds with #NACK
General command and reply message format
Any ASCII command has to start with the start delimiter #.
Any ASCII command has to end with simple carriage return (ASCII code 13)
Commands can be sent upper or lower case.
Reply messages from Flasher are sent back using the same format. All characters are upper case in
reply messages.
Communication port settings
Flasher is driven via RS232 serial port with the following interface settings:
8 data bits,
ODD parity
1 stop bit
at 115200 baud.
Commands to Flasher
The following commands are supported by current version of Flasher firmware:
#AUTO
The Auto command behaves exactly as the start button or external remote control input.
?
?
?
?
Flasher starts clearing target, if “automatic clear before program“ option was set.
Flasher programs target CPU
Flasher verifies target CPU
Flasher verifies its internal CRC to validate the programming operation.
Finally, Flasher responds with
?
?
#OK if no error occurred
#ERRxxx if any error occurred during operation. xxx represents the errorcode, normally replied to
Flasher PC program. The #ERRxxx message may be followed by an additional error text.
During execution of the AUTO command, Flasher automatically sends “status” messages via RS232
to reflect the state of execution. Typically during execution of #AUTO command, Flasher will reply the
following sequence of messages:
#ACK
#STATUS:START CMD
#STATUS:CONNECTING
#STATUS:CLEARING
#STATUS:WRITING
#STATUS:VERIFYING
#STATUS:VERIFY FLASHER CRC
#STATUS:READY
#OK
? 2004 - 2012 Segger Microcontroller GmbH & CoKG
相关PDF资料 |
PDF描述 |
|---|---|
| 5.09.01 FLASHER STM 8 | PROGRAMMING TOOL FOR STM8 |
| 5-103948-7 | 2X8 MTE SHRD PIN SR LTCH .100 |
| 5-103953-4 | 4X5 MTE PIN SR RIBBED .100CL |
| 5-103955-4 | 4X5 MTE PIN SR RIBBED .100CL |
| 5-103968-2 | 8X3 MTE RCPT SR RIBBED .1010CL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 505020 | 功能描述:TAG MARKING TERM BLOCK 1-10 RoHS:是 类别:连接器，互连式 >> 接线座 - 配件 - 标记条 系列:DY5 标准包装:10 系列:Dekafix 类型:标签，卡入式 图例:编号 189 间距:0.197"（5.00mm） 适用于相关产品:GSE、LP、LU、LX、P、SAK、W、Z 和 TOP 1.5GS 系列 颜色:白 包装:每张卡 50 个 |
| 50502-01 | 制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:Surge Protector Test Set |
| 505020-2 | 制造商:TE Connectivity 功能描述:250 FUSE RCPT - Tape and Reel |
| 5050205218 1/2 | 制造商:Wera 功能描述:50MM 1/4 SQUARE ADAPTOR |
| 505-021 | 制造商:CRANFORD CONTROLS 功能描述:SOUNDER 12/24VDC RED |
发布紧急采购，3分钟左右您将得到回复。