- 您现在的位置：买卖IC网 > Datasheet目录290 > 5.05.01 FLASHER 5 (Segger Microcontroller Systems)PROGRAMMING TOOL FOR MCU Datasheet资料下载
参数资料
| 型号： | 5.05.01 FLASHER 5 |
| 厂商： | Segger Microcontroller Systems |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | PROGRAMMING TOOL FOR MCU |
| 标准包装： | 1 |
| 类型： | 系统内编程器 |
| 适用于相关产品： | Renesas MCUs |
| 所含物品： | 编程器 |
| 产品目录页面： | 737 (CN2011-ZH PDF) |
| 其它名称： | 899-1001 |
ASCII command interface to Flasher V2.00
Segger Microcontroller GmbH & CoKG
#AUTO NOINFO
This command may be used instead of AUTO, if no status messages from Flasher should be sent
during execution.
The command ends with #OK or #ERRxxx
#BLANK
This command can be sent to perform a blank check over all selected target Flash sectors.
Flasher will reply the following sequence of messages:
#ACK
#STATUS:START CMD
#STATUS:CONNECTING
#STATUS:RESET
#STATUS:CONNECTING
#STATUS:BLANK CHECK
#STATUS:READY
#OK
in case of blank check failure, Flasher will respond with
#ERR004:BLANK CHECK FAILED .
#CLEAR
This command can be sent to clear all selected target Flash sectors.
Flasher will reply the following sequence of messages:
#ACK
#STATUS:START CMD
#STATUS:CONNECTING
#STATUS:RESET
#STATUS:CONNECTING
#STATUS:CLEARING
#STATUS:READY
#OK
in case of an erase failure, Flasher will respond with
#ERR001:ERASE FAILED .
or an other error message if any communication error occured.
#CLEARALL
This command can be used with Flasher ST7 to remove the read out protection of ST7 target CPUs.
The read out protection is removed and the whole target Flash area is erased.
#START
This command can be sent to release Flashers target interface. All signals from Flasher to target will
be set into high-Z mode, reset of target will be released. May be used to start target application pro-
gram.
Flasher will reply the following sequence of messages:
#ACK
#STATUS:START CMD
#STATUS:READY
#OK
#CRC
This command is useful to identify or verify Flashers internal data which should be programmed to
target CPU.
Flasher responds with the CRC of its current memory content:
? #CRC:xxxx if data is present. xxxx is a 4 digit HEX number.
?
#CRC:---- if no valid data is present in Flashers memory
#STATUS
This command can be sent any time, even during other command execution. Flasher responds with its
current state. All defined state messages are described under “Flasher reply messages from Flasher”
later on in this manual.
? 2004 – 2012 Segger Microcontroller GmbH & CoKG
相关PDF资料 |
PDF描述 |
|---|---|
| 5.09.01 FLASHER STM 8 | PROGRAMMING TOOL FOR STM8 |
| 5-103948-7 | 2X8 MTE SHRD PIN SR LTCH .100 |
| 5-103953-4 | 4X5 MTE PIN SR RIBBED .100CL |
| 5-103955-4 | 4X5 MTE PIN SR RIBBED .100CL |
| 5-103968-2 | 8X3 MTE RCPT SR RIBBED .1010CL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 505020 | 功能描述:TAG MARKING TERM BLOCK 1-10 RoHS:是 类别:连接器，互连式 >> 接线座 - 配件 - 标记条 系列:DY5 标准包装:10 系列:Dekafix 类型:标签，卡入式 图例:编号 189 间距:0.197"（5.00mm） 适用于相关产品:GSE、LP、LU、LX、P、SAK、W、Z 和 TOP 1.5GS 系列 颜色:白 包装:每张卡 50 个 |
| 50502-01 | 制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:Surge Protector Test Set |
| 505020-2 | 制造商:TE Connectivity 功能描述:250 FUSE RCPT - Tape and Reel |
| 5050205218 1/2 | 制造商:Wera 功能描述:50MM 1/4 SQUARE ADAPTOR |
| 505-021 | 制造商:CRANFORD CONTROLS 功能描述:SOUNDER 12/24VDC RED |
发布紧急采购，3分钟左右您将得到回复。