- 您现在的位置：买卖IC网 > Datasheet目录600 > 58425-3 (TE Connectivity)TOOL DIE SET COAX RG59 DB Datasheet资料下载
参数资料
| 型号： | 58425-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 1/4页 |
| 文件大小： | 0K |
| 描述： | TOOL DIE SET COAX RG59 DB |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 压接手柄： | A9996-ND |
| 连接器类型： | BNC，TNC |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A1860 A1860-ND A9959 |
75-Ohm Hex Crimp ?
Die Assemblies ?
58425-[ ] and 58436-[ ]
Instruction Sheet
408-9657
14 OCT 11 Rev E
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use
and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
Anvil Die
Die Assemblies 58425-[ ]
and 58436-[ ]
Stationary Jaw
Hand Tool Frame
354940-1
Indenter Die
Moving Jaw
Figure 1
1. INTRODUCTION
This instruction sheet covers the use and maintenance
of Crimping Dies 58425-[ ] and58436-[ ] (in their
various configurations - denoted by the dash number
following the base part number), used in PRO-
CRIMPER III Hand Tool Frame 354940-1. The dies
crimp 75-Ohm Hex Crimp BNC and TNC plug
connectors onto coaxial cable.
Reasons for reissue of this sheet are provided in
Section 7, REVISION SUMMARY.
2. DESCRIPTION (Figure 1 )
Each die assembly consists of an indenter die and an
anvil die. When closed, the dies form either two or
three crimping chambers (depending on type) which
crimp the center contact and ferrule of the connector
onto the coaxial cable. Each die is held in the tool by a
single screw.
3. DIE INSTALLATION
1. Close the tool handles until the ratchet releases
?
NOTE
i
All dimensions are in millimeters [with inches in
brackets]. Figures and illustrations are for
reference only and are not drawn to scale.
and then allow them to open fully.
2. See Figure 1 for normal orientation of the dies.
Insert the dies inside the tool jaws and align the
retaining screw holes.
3. Thread the retaining screws into the holes and
carefully close the tool handles. Tighten the screws
with the appropriate hex wrench.
? 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company ?
All Rights Reserved
*Trademark
TOOLING ASSISTANCE CENTER 1-800-722-1111 ?
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change. ?
For latest revision and Regional Customer Service,
visit our website at www.te.com
1 of 4
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
LOC B
相关PDF资料 |
PDF描述 |
|---|---|
| 58430-1 | TOOL REPAIR .050 SERIES |
| 58432-1 | TOOL DIE SET |
| 58433-4 | TOOL CRIMP F/OPTIC ST & SC |
| 58442-1 | TOOL HEAD ASSEMBLY RCPT MTA 100 |
| 58443-1 | TOOL HEAD ASSEMBLY MTA .156 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 584259-000 | 制造商:TE Connectivity 功能描述:Cable Accessories Transition Semi-Rigid Modified Polyolefin 制造商:TE Connectivity 功能描述:322A112-3/86-0 - Bulk 制造商:TE Connectivity 功能描述:BOOT MOLDED |
| 58426HV | 功能描述:速度传感器 FMD MS3106A RoHS:否 制造商:Honeywell 最大工作温度:+ 120 C 电源电压: 电源电流: 输出电压:190 V 工作电源电压: 安装风格:Screw 最小工作温度:- 55 C 系列:High Output VRS |
| 58426HVA30 | 功能描述:速度传感器 ELECTRO RoHS:否 制造商:Honeywell 最大工作温度:+ 120 C 电源电压: 电源电流: 输出电压:190 V 工作电源电压: 安装风格:Screw 最小工作温度:- 55 C 系列:High Output VRS |
| 58426LV | 功能描述:速度传感器 FMD 5V MS3106A RoHS:否 制造商:Honeywell 最大工作温度:+ 120 C 电源电压: 电源电流: 输出电压:190 V 工作电源电压: 安装风格:Screw 最小工作温度:- 55 C 系列:High Output VRS |
| 58426LVA30 | 功能描述:速度传感器 ELECTRO RoHS:否 制造商:Honeywell 最大工作温度:+ 120 C 电源电压: 电源电流: 输出电压:190 V 工作电源电压: 安装风格:Screw 最小工作温度:- 55 C 系列:High Output VRS |
发布紧急采购，3分钟左右您将得到回复。