- 您现在的位置：买卖IC网 > Datasheet目录600 > 58442-1 (TE Connectivity)TOOL HEAD ASSEMBLY RCPT MTA 100 Datasheet资料下载
参数资料
| 型号： | 58442-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | TOOL HEAD ASSEMBLY RCPT MTA 100 |
| 特色产品： | MTA Connectors |
| 标准包装： | 1 |
| 系列： | MTA-100 |
| 压接或电缆尺寸： | 22 AWG and 28 AWG |
| 压接手柄： | A2031-ND，58075-1-ND，58338-1-ND，931800-1-ND |
| 连接器类型： | 矩形 |
| 产品目录页面： | 199 (CN2011-ZH PDF) |
| 相关产品： | A2031-ND - TOOL MANUAL FOR SHELL CONNECTORS |
| 其它名称： | 58442-1-ND A9973 |
the direction of the arrow) until it stops, then
release the trigger or foot pedal (the receptacle
should advance so that the first contact aligns with
the wire inserter).
4. Check that the locating pawl is resting between
the index ribs of the receptacle. See Figure 2. If
not, push the receptacle out of the RIGHT side of
the head, and re–insert it.
5. Insert an unstripped wire into the funnel area
between the contact and the wire inserter until it is
in the desired location to be terminated.
6. Actuate the tool according to the instructi ons
included with the tool. When the cycle is
completed, the wire inserter will retract, and the
feed slide will automatically advance the receptacle
to the next contact position.
Figure 3
7. Repeat Steps 4 through 6 until all contacts have
been terminated.
8. Inspect each termination according to Section 5.
Refer to Figure 3, and inspect each termination to
ensure the following:
— the wire is terminated past the lead–in transition
and is about halfway in the contact slot
— the wire is from 1.78 to 2.16 mm [.070 to
.085 in.] beyond the front of the contact beam
— the wire is NOT bottomed in the contact slot
— the contact beams are NOT deformed (if
damage is apparent, replace the contacts in
accordance with the instructions packaged with the
receptacle)
— the wire is NOT nicked or cut in any area other
than the contact slot
— the wires extend beyond the strain–reliefs of the
receptacle
Figure 4
The following procedures have been established to
ensure the quality and reliability of the head. The
head should be checked daily, and a more detailed
inspection should be performed by your quality control
group on a regular basis.
Each operator should be aware of, and responsible
for, the following steps of maintenance.
相关PDF资料 |
PDF描述 |
|---|---|
| 58443-1 | TOOL HEAD ASSEMBLY MTA .156 |
| 58448-2 | CRIMP TOOL D-SUB TERMINALS |
| 58483-1 | TOOL SMB DIE SET CONN MIL TYPE |
| 58500-1 | TOOL CRIMP SMB RG/174 W/DIE SET |
| 58509-1 | DIE SET 22-10AWG BUDGET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58442-101 | 功能描述:I/O 连接器 12X Plug Kit - Latch, 24 Signal Pairs RoHS:否 制造商:Hirose Connector 产品:Plugs 系列:DH 端口数量: 位置/触点数量:51 节距:1 mm 触点电镀: 触点材料: 型式:Male 电流额定值:0.5 A 安装风格:Cable 端接类型:IDC 颜色: 安装角: |
| 58442-101LF | 功能描述:I/O 连接器 12X PLUG KIT W/UNEQUALIZ-P2 PCB RoHS:否 制造商:Hirose Connector 产品:Plugs 系列:DH 端口数量: 位置/触点数量:51 节距:1 mm 触点电镀: 触点材料: 型式:Male 电流额定值:0.5 A 安装风格:Cable 端接类型:IDC 颜色: 安装角: |
| 58442-103LF | 功能描述:I/O 连接器 RoHS:否 制造商:Hirose Connector 产品:Plugs 系列:DH 端口数量: 位置/触点数量:51 节距:1 mm 触点电镀: 触点材料: 型式:Male 电流额定值:0.5 A 安装风格:Cable 端接类型:IDC 颜色: 安装角: |
| 58442-104LF | 功能描述:I/O 连接器 12X PLUG KIT W/EQUALIZED-P2 PCB RoHS:否 制造商:Hirose Connector 产品:Plugs 系列:DH 端口数量: 位置/触点数量:51 节距:1 mm 触点电镀: 触点材料: 型式:Male 电流额定值:0.5 A 安装风格:Cable 端接类型:IDC 颜色: 安装角: |
| 58443-001 | 功能描述:I/O 连接器 PLUG SUB ASSY EYEMAX RoHS:否 制造商:Hirose Connector 产品:Plugs 系列:DH 端口数量: 位置/触点数量:51 节距:1 mm 触点电镀: 触点材料: 型式:Male 电流额定值:0.5 A 安装风格:Cable 端接类型:IDC 颜色: 安装角: |
发布紧急采购，3分钟左右您将得到回复。