- 您现在的位置：买卖IC网 > PDF目录19180 > 58499-1 (TE Connectivity)TOOL PRO CRIMPER II W/DI PDF资料下载
参数资料
| 型号： | 58499-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/3页 |
| 文件大小： | 0K |
| 描述： | TOOL PRO CRIMPER II W/DI |
| 标准包装： | 5 |
| 系列： | Pro-Crimper III |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 同轴，RF - SMB |
| 特点： | 侧面插入，棘齿 |
| 其它名称： | Q1907823 |
The tool frame features a stationary jaw and handle, a
moving jaw, a moving handle, and an adjustable
ratchet that ensures full crimping. The tool frame
holds the die assembly.
The die assembly consists of an indenter (stationary
die) and an anvil (moving die). When closed, the dies
form three crimping chambers. Each die is held in the
hand tool frame by a single screw.
Make sure that the center contact is properly crimped
and assembled onto the connector as described in
applicable connector instruction sheet. Then proceed
as follows:
1. Slide the ferrule over the cable braid until it is
positioned against the shoulder of the plug body.
2. Close the tool handles until the ratchet releases,
then allow the handles to open FULLY.
3. Place the ferrule in the appropriate crimping
chamber on the anvil die so that the shoulder of
the plug body is close to the edge of the die. Refer
to Figure 3.
1. Close the tool handles until the ratchet releases,
then allow the handles to open fully.
2. Insert the dies into the tool jaws as shown in
Figure 2, and align the retaining holes in each die
with the associated hole in the tool.
Figure 3
4. While holding the assembly, close the tool
handles until the dies hold the ferrule in place.
5. Carefully close the tool handles until the ratchet
releases, then allow the handles to open FULLY.
Figure 2
3. Thread, but do not tighten, the die retaining
screws into the holes.
4. Carefully close the tool handles, making sure
that the dies align properly.
5. Tighten the die retaining screws with the
appropriate hex wrench.
6. To disassemble, close the tool handles until the
ratchet releases, remove the two die retaining
screws, and slide the dies out of the tool jaws.
6. Remove the ferrule from the dies.
7. Inspect the crimped ferrule according to
applicable connector instruction sheet. If
necessary, adjust the ratchet as described in
Section 5.
The tool ratchet mechanism features an adjustment
wheel with numbered settings. The adjustment wheel
controls the amount of handle pressure exerted on
the jaws during crimping. If the crimp is not
acceptable, adjust the ratchet as follows:
1. Remove the lockscrew from the ratchet
adjustment wheel.
相关PDF资料 |
PDF描述 |
|---|---|
| A6S-7104-PH | SWITCH DIP 7POS RAISED SMD |
| 5370T1LC | LED RED T-3/4 VERT LOW CUR PCB |
| DP04T | PIANO STYLE DIP SWITCH |
| A6HF-4102-PM | SWITCH DIP 4POS HALF PITCH SMD |
| A6SN-7101-P | SWITCH DIP 7POS FLUSH ACT SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5849EAG1W00140 | 功能描述:IO NICU CF V0 制造商:laird technologies emi 系列:* 零件状态:过期 标准包装:228 |
| 5849EBG1W00229 | 制造商:Laird Technologies Inc 功能描述:IO,NICU,CF,V0 / .040X.700X2.290 / UOM=EA |
| 584A-10.016-1 | 制造商:Fox Electronics 功能描述:- Tape and Reel |
| 584A-25-6 | 制造商:Fox Electronics 功能描述:- Cut Tape Product 制造商:Fox Electronics 功能描述:- Tape and Reel |
| 584A-50-2 | 制造商:Fox Electronics 功能描述:- Cut Tape Product |
发布紧急采购，3分钟左右您将得到回复。