- 您现在的位置：买卖IC网 > Datasheet目录601 > 58519-1 (TE Connectivity)TOOL CRIMP F/OPTIC FSD STYLE Datasheet资料下载
参数资料
| 型号： | 58519-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMP F/OPTIC FSD STYLE |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 光纤 - FSD |
| 特点： | 侧面插入，棘齿 |
| 配用： | 5502015-3-ND - KIT, CONN, FSD, 125 UM, LDD 5501780-3-ND - CONN KIT, DUALAN, FSD, 125 UM 5502015-1-ND - KIT,CONN,FSD,125UM,LDD 5501780-1-ND - CONN KIT,DUALAN,FSD,125UM 502020-1-ND - BREAKOUT KIT ASSY,FSD AND RSD 501780-4-ND - CONN KIT,DUALAN,FSD,NO SR,BULK 501780-3-ND - CONN PLUG DUALAN 125MICRON KIT 501780-1-ND - CONN KIT,DUALAN,FSD,125UM |
| 其它名称： | A99107 |
PRO- CRIMPER III Hand Crimping Tool Assembly 58519- 1
408- 9917
Stationary Jaw
Indenter Die
Die-- Retaining
Screws
Anvil Die
Movable
Jaw
Figure 2
Ratchet
3. DIE INSTALLATION (Figure 2)
1. Close the tool handles until the ratchet releases;
then allow the tool handles to open FULLY.
2. Install anvil die in the movable jaw of the tool
frame. Align the die with the retaining screw hole;
then secure die with the die--retaining screw. Do
NOT fully tighten.
3. Install indenter die in the stationary jaw of the
tool frame. Slowly close the tool handles, allowing
the dies to align themselves. When dies are
properly aligned, securely tighten both screws with
the appropriate hex wrench.
4. CRIMPING PROCEDURE (Figure 3)
Prepare connector and cable according to the
instructions packaged with the connector, and
proceed as follows:
1. Close the tool handles until the ratchet releases;
then allow the tool handles to open FULLY.
2. Place the strain relief assembly (with the outer
crimp ring in place) in the appropriate crimping
chamber so that the flange of the strain relief rests
against the sides of the die. See Figure 3.
3. Close the tool handles until the ratchet releases;
then open the tool handles to remove the crimped
connector.
5. MAINTENANCE/INSPECTION
5.1. Maintenance
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or a clean, soft, lint--free
cloth. Do NOT use any objects that could damage
the dies or tool.
2. Make sure that the proper die--retaining screws
are properly secured.
3. When the dies are not in use, store them in a
clean, dry area.
4. Store the tool with the tool handles closed to
prevent objects from becoming lodged within the
jaws.
5.2. Inspection
1. Remove all lubrication and accumulated film
from the dies by immersing the dies in a suitable
commercial degreaser.
2. Make certain that all die--retaining screws and
die components are properly secured.
3. Inspect the crimping surfaces for flattened,
chipped, worn, or cracked areas. If damage is
evident, the dies must be replaced. Refer to
Section 6, REPLACEMENT.
2 of 4
Tyco Electronics Corporation
Rev B
相关PDF资料 |
PDF描述 |
|---|---|
| 58529-2 | TOOL DIE SET CRIMP TERMINAL |
| 58532-1 | TOOL FIBER OPTIC PRO CRIMPER III |
| 58541-2 | TOOL DIE FOR PRO-CRIMPER II |
| 58545-1 | DIE SET UNINSULATED TERMINALS |
| 58558-1 | CONSUMER BNC TOOL RG 58/59 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5851-9SL005 | 制造商:Alpha Wire Company 功能描述:Grey hook-up equipment wire,30awg |
| 5851A20003J | 制造商:LG Corporation 功能描述:Drier Assembly |
| 5851A20003M | 制造商:LG Corporation 功能描述:Drier Assembly |
| 5851A30001A | 制造商:LG Corporation 功能描述:DRIER ASSY |
| 5851A30001D | 制造商:LG Corporation 功能描述:Drier Assembly |
发布紧急采购，3分钟左右您将得到回复。