- 您现在的位置：买卖IC网 > PDF目录67328 > 5962-8967802XA (ANALOG DEVICES INC) QUAD, PARALLEL, 8 BITS INPUT LOADING, 0.19 us SETTLING TIME, 8-BIT DAC, CDIP28 PDF资料下载
参数资料
| 型号： | 5962-8967802XA |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | DAC |
| 英文描述： | QUAD, PARALLEL, 8 BITS INPUT LOADING, 0.19 us SETTLING TIME, 8-BIT DAC, CDIP28 |
| 封装： | 0.600 INCH, GLASS SEALED, CERDIP-28 |
| 文件页数： | 2/17页 |
| 文件大小： | 223K |
| 代理商： | 5962-8967802XA |
DAC8408
–10–
REV. A
BASIC APPLICATIONS
Some basic circuit configurations are shown in Figures 6 and 7.
Figure 6 shows the DAC8408 connected in a unipolar configu-
ration (2-Quadrant Multiplication), and Table I shows the Code
Table. Resistors R1, R2, R3, and R4 are used to trim full scale
output. Full-scale output voltage = VREF –1 LSB = VREF (1–2
–8)
or VREF × (255/256) with all digital inputs high. Low tempera-
ture coefficient (approximately 50 ppm/
°C) resistors or trim-
mers should be selected if used. Full scale can also be adjusted
using VREF voltage. This will eliminate resistors R1, R2, R3, and
R4. In many applications, R1 through R4 are not required, and
the maximum gain error will then be that of the DAC.
Each DAC exhibits a variable output resistance that is code-
dependent. This produces a code-dependent, differential non-
linearity term at the amplifier’s output which can have a maxi-
mum value of 0.67
× the amplifier’s offset voltage. This differ-
ential nonlinearity term adds to the R-2R resistor ladder differ-
ential-nonlinearity; the output may no longer be monotonic. To
maintain monotonicity and minimize gain and linearity errors, it
is recommended that the op amp offset voltage be adjusted to
less than 10% of 1 LSB (1 LSB = 2
–8
× V
REF or 1/256
× V
REF),
or less than 3.9 mV over the operating temperature range. Zero-
scale output voltage (with all digital inputs low) may be adjusted
using the op amp offset adjustment. Capacitors C1, C2, C3,
and C4 provide phase compensation and help prevent overshoot
and ringing when using high speed op amps.
Figure 7 shows the recommended circuit configuration for the
bipolar operation (4-quadrant multiplication), and Table II shows
the Code Table. Trimmer resistors R17, R18, R19, and R20
are used only if gain error adjustments are required and range
between 50
and 1000 . Resistors R21, R22, R23, and R24
will range betwen 50
and 500 . If these resistors are used, it
is essential that resistor pairs R9–R13, R10–R14, R11–R15,
R12–R16 are matched both in value and tempco. They should
be within 0.01%; wire wound or metal foil types are preferred
for best temperature coefficient matching. The circuits of Figure
6 and 7 can either be used as a fixed reference D/A converter, or
as an attenuator with an ac input voltage.
Table I. Unipolar Binary Code Table (Refer to Figure 6)
DAC Data Input
MSB
LSB
Analog Output
1 1 1 1 1 1 1 1
–VREF
255
256
1 0 0 0 0 0 0 1
–VREF
129
256
1 0 0 0 0 0 0 0
–VREF
128
256
=
–VIN
2
0 1 1 1 1 1 1 1
–VREF
127
256
0 0 0 0 0 0 0 1
–VREF
1
256
0 0 0 0 0 0 0 0
–VREF
0
256
= 0
NOTE
1 LSB = (2
–8) (V
REF) =
1
256
(VREF)
Figure 6. Quad DAC Unipolar Operation (2-Quadrant Multiplication)
相关PDF资料 |
PDF描述 |
|---|---|
| 5962-8967901QX | 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, CDIP40 |
| 5962-8967901XX | 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, CQCC44 |
| 5962-8968303HZA | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| 5962-9158001HZA | 1-OUTPUT 20 W DC-DC REG PWR SUPPLY MODULE |
| 5962-9162501HZA | 1-OUTPUT 20 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5962-8967901XC | 制造商:SEI 功能描述: |
| 5962-89680012A | 制造商:Texas Instruments 功能描述:Octal Transmitter/Receiver 20-Pin LCCC Tube |
| 5962-89680012A-T | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| 5962-8968001RA | 制造商:Texas Instruments 功能描述:Octal Transmitter/Receiver 20-Pin CDIP Tube 制造商:Texas Instruments 功能描述:LINE TRNSCVR 8TR 8TX 8RX 20CDIP - Rail/Tube |
| 5962-8968001SA | 制造商:Texas Instruments 功能描述:Octal Transmitter/Receiver 20-Pin CFPAK Tube 制造商:Rochester Electronics LLC 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。