- 您现在的位置：买卖IC网 > PDF目录97780 > 5962R8771003VPA (NATIONAL SEMICONDUCTOR CORP) DUAL OP-AMP, 4000 uV OFFSET-MAX, 1 MHz BAND WIDTH, CDIP8 PDF资料下载
参数资料
| 型号： | 5962R8771003VPA |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 运算放大器 |
| 英文描述： | DUAL OP-AMP, 4000 uV OFFSET-MAX, 1 MHz BAND WIDTH, CDIP8 |
| 封装： | CERAMIC, DIP-8 |
| 文件页数： | 4/26页 |
| 文件大小： | 494K |
| 代理商： | 5962R8771003VPA |
Application Hints
The LM158 series are op amps which operate with only a
single power supply voltage, have true-differential inputs, and
remain in the linear mode with an input common-mode volt-
age of 0 V
DC. These amplifiers operate over a wide range of
power supply voltage with little change in performance char-
acteristics. At 25°C amplifier operation is possible down to a
minimum supply voltage of 2.3 V
DC.
Precautions should be taken to insure that the power supply
for the integrated circuit never becomes reversed in polarity
or that the unit is not inadvertently installed backwards in a
test socket as an unlimited current surge through the resulting
forward diode within the IC could cause fusing of the internal
conductors and result in a destroyed unit.
Large differential input voltages can be easily accommodated
and, as input differential voltage protection diodes are not
needed, no large input currents result from large differential
input voltages. The differential input voltage may be larger
than V+ without damaging the device. Protection should be
provided to prevent the input voltages from going negative
more than 0.3 V
DC (at 25°C). An input clamp diode with a
resistor to the IC input terminal can be used.
To reduce the power supply current drain, the amplifiers have
a class A output stage for small signal levels which converts
to class B in a large signal mode. This allows the amplifiers
to both source and sink large output currents. Therefore both
NPN and PNP external current boost transistors can be used
to extend the power capability of the basic amplifiers. The
output voltage needs to raise approximately 1 diode drop
above ground to bias the on-chip vertical PNP transistor for
output current sinking applications.
For ac applications, where the load is capacitively coupled to
the output of the amplifier, a resistor should be used, from the
output of the amplifier to ground to increase the class A bias
current and prevent crossover distortion. Where the load is
directly coupled, as in dc applications, there is no crossover
distortion.
Capacitive loads which are applied directly to the output of the
amplifier reduce the loop stability margin. Values of 50 pF can
be accommodated using the worst-case non-inverting unity
gain connection. Large closed loop gains or resistive isolation
should be used if larger load capacitance must be driven by
the amplifier.
The bias network of the LM158 establishes a drain current
which is independent of the magnitude of the power supply
voltage over the range of 3 V
DC to 30 VDC.
Output short circuits either to ground or to the positive power
supply should be of short time duration. Units can be de-
stroyed, not as a result of the short circuit current causing
metal fusing, but rather due to the large increase in IC chip
dissipation which will cause eventual failure due to excessive
junction temperatures. Putting direct short-circuits on more
than one amplifier at a time will increase the total IC power
dissipation to destructive levels, if not properly protected with
external dissipation limiting resistors in series with the output
leads of the amplifiers. The larger value of output source cur-
rent which is available at 25°C provides a larger output current
capability at elevated temperatures (see typical performance
characteristics) than a standard IC op amp.
The circuits presented in the section on typical applications
emphasize operation on only a single power supply voltage.
If complementary power supplies are available, all of the stan-
dard op amp circuits can be used. In general, introducing a
pseudo-ground (a bias voltage reference of V+/2) will allow
operation above and below this value in single power supply
systems. Many application circuits are shown which take ad-
vantage of the wide input common-mode voltage range which
includes ground. In most cases, input biasing is not required
and input voltages which range to ground can easily be ac-
commodated.
www.national.com
12
LM158QML
相关PDF资料 |
PDF描述 |
|---|---|
| 5962R8771003VXA | DUAL OP-AMP, 4000 uV OFFSET-MAX, 1 MHz BAND WIDTH, CDSO10 |
| 5962R8771002VGA | DUAL OP-AMP, 4000 uV OFFSET-MAX, 1 MHz BAND WIDTH, MBCY8 |
| 5962R8771002VPA | DUAL OP-AMP, 4000 uV OFFSET-MAX, 1 MHz BAND WIDTH, CDIP8 |
| 5962R8771002VXA | DUAL OP-AMP, 4000 uV OFFSET-MAX, 1 MHz BAND WIDTH, CDSO10 |
| 5962-8771001MGA | DUAL OP-AMP, 7000 uV OFFSET-MAX, 1 MHz BAND WIDTH, MBCY8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5962R8771003VXA | 功能描述:运算放大器 - 运放 RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| 5962R8773901V2A | 制造商:Analog Devices 功能描述:TRANSDUCER IC SPACE PRODUCT - Rail/Tube |
| 5962R8773901VCA | 制造商:Analog Devices 功能描述:- Rail/Tube |
| 5962R8773901VDA | 制造商:Analog Devices 功能描述:COMPARATOR QUAD 15V/30V 14PIN FLATPACK - Rail/Tube |
| 5962R8775901SSA | 制造商:Texas Instruments 功能描述: |
发布紧急采购，3分钟左右您将得到回复。