- 您现在的位置：买卖IC网 > Datasheet目录602 > 64007-0100 (Molex Connector Corporation)TOOL HEAD ASSY FOR 19279-0002 Datasheet资料下载
参数资料
| 型号： | 64007-0100 |
| 厂商： | Molex Connector Corporation |
| 文件页数： | 11/15页 |
| 文件大小： | 0K |
| 描述： | TOOL HEAD ASSY FOR 19279-0002 |
| 其它有关文件： | Overlap Style Insulation Crimps |
| 标准包装： | 1 |
| 系列： | AT-200™ |
| 压接或电缆尺寸： | 10-22 AWG |
| 压接手柄： | Molex 19279-0002 |
| 连接器类型： | 端子及连接件 |
| 配用： | 0192070001-ND - PARALLEL SPLICE VERSAKRIMP 0191410063-ND - SPADE KRIMPTITE (BB-127-08) 0191410056-ND - SPADE KRIMPTITE (BB-124-06) 0191470062-ND - BLOCK SPADE VERSAKRIMP 0191410024-ND - SPADE KRIMPTITE (AA-135-10) 0191410020-ND - SPADE KRIMPTITE (AA-135-06) 0191410022-ND - SPADE KRIMPTITE (AA-135-08) 0191470057-ND - BLOCK SPADE VERSAKRIMP 0191470090-ND - BLOCK SPADE VERSAKRIMP 0191410065-ND - SPADE KRIMPTITE (BB-127-10) 更多... |
| 相关产品： | WM6454-ND - TOOL HAND CRIMPER PNEUM |
| 其它名称： | 064007-0100 064007-0100-E 0640070100 0640070100-E 64007-0100-E 64007-0100-ND 640070100 640070100-E WM5018 |
AT-1992 Hand Crimp Tool
JAWS OPEN
Operation
SAFETY
Refer to the instruction manual for the 19279-
0001 (AT-200) for mounting this crimp tool head.
Crimping Terminals
SHIELD
FRONT EDGE
OF BARREL
1. Adjust the locator up or down until the
terminal being run sits flat and straight in the
tool.
TERMINAL
LOCATOR
Figure 1
PUSH UP TO
LOAD TERMINAL
2. Insert the wire into the terminal. Push up on the locator blade and insert the terminal and wire into the proper
nest with the barrel up and against the locator bar. Release the locator blade to hold the terminal in position. See
Figure 1. Locator may be raised or lowered so terminal sits flat and straight in tool. The locator must be removed
to run splices.
Caution: Never operate this tool without the supplied safety shield in place. Never place fingers in the tool nests.
3. Push on the wire to assure it is fully seated in the terminal. See Figure 2 and 3. The
wires end should butt against the wire stop position of the locator. Cycle the tool.
4. Lift the locator blade or wire stop and remove the crimped terminal. Inspect for proper
crimp location. Locator is adjustable up and down to keep terminals straight after
crimping.
5. When crimping butt splices, the locator must be removed. Insert the wire into the butt
splice. Position the splice and the wire in proper coded nest with conductor crimp on the
conductor barrel of the splice The splice should be approximately centered inside the
LOCATOR
tooling nests. See Figure 4. Cycle the tool.
CONDUCTOR
ANVIL
TERMINAL
BUTT
SPLICE
CONDUCTOR
ANVIL
WIRE
WIRE
TERMINAL
Figure 2
BARREL
TERMINAL
CONDUCTOR
PUNCH
Figure 3
WIRE
CONDUCTOR
PUNCH
Figure 4
VISUALLY
CENTER SPLICE
BARREL
CONDUCTOR
Note : Whenever crimping without the locator, make sure the seam
ANVIL
of the terminal is oriented up or down in the tool if using unbrazed
product, as this will provide higher pull force values.
6. When crimping parallel splices, the locator must be removed.
Insert the 1 st wire into one end of splice then insert the 2 nd wire
into the opposite end of the parallel splice. This procedure will
crimp both wires at the same time. Make sure the wires are fully
seated into the parallel splice. Position the splice and the wires
PARALLEL
SPLICE
2 ND WIRE
1 ST WIRE
VISUALLY
in proper coded nest with conductor crimp on the conductor
barrel of the splice The splice should be approximately centered
CONDUCTOR
PUNCH
Figure 5
CENTER SPLICE
BARREL
inside the tooling nests. See Figure 5. Cycle the tool.
Doc No:ATS-640070100
Revision: J
Release Date: 10-03-02
Revision Date: 08-08-13
UNCONTROLLED COPY
Page 11 of 15
相关PDF资料 |
PDF描述 |
|---|---|
| 6534 | KIT BNC COAXIAL TEST LEADS 7PCS |
| 674655 | TOOL HAND DOUBLE ACTION |
| 68038 | PNEU HEAD BAR CRIMP 4AWG COPALUM |
| 68142-1 | DAHT PG FLAG 10-16AWG |
| 69008-0985 | TOOL HAND CRIMP 22-28AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 64007-0200 | 功能描述:折皱器 AT-1997 CRIMP TOOL H 1997 CRIMP TOOL HEAD RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 64007-0375 | 功能描述:折皱器 LOCATOR ASSEMBLY LOCATOR ASSEMBLY RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 64007-0400 | 功能描述:折皱器 AT-1753 CRIMP TOOL H 1753 CRIMP TOOL HEAD RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 64007-0500 | 功能描述:折皱器 AT-1412 CRIMP TOOL H 1412 CRIMP TOOL HEAD RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 64007055 | 制造商:FAS Controls 功能描述:AUTO SS - SHELB 制造商:KENDRION INC. 功能描述:AUTO SS - SHELB |
发布紧急采购，3分钟左右您将得到回复。