- 您现在的位置：买卖IC网 > Datasheet目录602 > 69254-1 (TE Connectivity)DIE PO INSUL SPLICE 69099 2/0 Datasheet资料下载
参数资料
| 型号： | 69254-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | DIE PO INSUL SPLICE 69099 2/0 |
| 标准包装： | 1 |
| 系列： | * |
| 相关产品： | 1752868-1-ND - HYDRAULIC CRIMP C-HEAD |
3. Engage the holding device on the power unit so
that the ram stays in position.
4. Loosen the ram setscrew.
5. Align the lower die with the upper die as shown
in Figure 2. Insert the shank on the lower die
partially into the ram well, making sure the shank is
facing the setscrew. Do NOT allow the dies to
become disengaged.
6. Activate the power unit and advance the ram
just enough to move the lower die to its topmost
1. Assemble the insulating sleeve over the crimped
wire barrel of the terminal or splice as shown in
Figure 3. Make sure the bushing butts against, but
does not slide over, the crimped cartridge.
2. Check that the insulating sleeve extends
approximately 0.80 mm [.031 in.] from the ring and
that the bushing extends approximately 0.80 mm
[.031 in.] from the insulating sleeve. Refer to
Figure 3.
position before completing a cycle.
7. Engage the holding device. Tighten both
setscrews.
3. Center the ring on the insulating sleeve in
the crimping chamber of the stationary die.
See Figure 4.
8. Activate power unit and allow the ram to return
to the ‘‘DOWN” position.
4. Activate power unit to complete the crimp.
5. To crimp the other half of a splice, reposition the
Loosen setscrew in top of crimping head and remove
upper die. Raise the ram until the ram setscrew is
visible. Loosen ram setscrew and remove lower die.
Figure 3
uncrimped side in the crimping chamber.
6. Remove crimped terminal or splice from die and
inspect the crimp.
相关PDF资料 |
PDF描述 |
|---|---|
| 69272-1 | TOOL HAND CRIMP STRATO-THERM |
| 69322-1 | TOOL HAND CRIMP SPLICE 10-12 AWG |
| 69331-1 | STR ACT DAHT COAXICON BNC |
| 69352 | HHHT TERMASHIELD SPLC 18-22AWG |
| 69357-3 | EXTRACT TOOL TERMI-POINT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 69255 | 制造商:FCI-CONNECTOR 制造商全称:FCI connector 功能描述:8 POS VERTICAL P.C.B. MOD JACK ASSY |
| 6925-5 | 制造商:Johanson Manufacturing 功能描述:TUNING ELEMENT |
| 69255-001 | 功能描述:以太网和电信连接器 PCB 8/8 VERTICAL RoHS:否 制造商:Pulse 产品:Modular Jacks 性能类别: USOC 代码:RJ45 位置/触点数量: 安装风格:Through Hole 端口数量:1 x 1 型式:Female 屏蔽: 电流额定值: 电压额定值: 触点电镀: 外壳材料:Thermoplastic IP 等级: |
| 69255-001LF | 功能描述:以太网和电信连接器 PCB 8/8 VERTICAL RoHS:否 制造商:Pulse 产品:Modular Jacks 性能类别: USOC 代码:RJ45 位置/触点数量: 安装风格:Through Hole 端口数量:1 x 1 型式:Female 屏蔽: 电流额定值: 电压额定值: 触点电镀: 外壳材料:Thermoplastic IP 等级: |
| 69255-001W | 功能描述:以太网和电信连接器 69255-001W-PCB MJ RoHS:否 制造商:Pulse 产品:Modular Jacks 性能类别: USOC 代码:RJ45 位置/触点数量: 安装风格:Through Hole 端口数量:1 x 1 型式:Female 屏蔽: 电流额定值: 电压额定值: 触点电镀: 外壳材料:Thermoplastic IP 等级: |
发布紧急采购，3分钟左右您将得到回复。