- 您现在的位置：买卖IC网 > Datasheet目录602 > 69254-1 (TE Connectivity)DIE PO INSUL SPLICE 69099 2/0 Datasheet资料下载
参数资料
| 型号： | 69254-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | DIE PO INSUL SPLICE 69099 2/0 |
| 标准包装： | 1 |
| 系列： | * |
| 相关产品： | 1752868-1-ND - HYDRAULIC CRIMP C-HEAD |
1. Remove accumulated dirt, grease, and foreign
matter from die closure surfaces of the dies. Wipe
dies frequently with a soft, lint–free cloth. Do NOT
use hard or abrasive objects that could damage
the dies.
2. When die assembly is not in use, mate and
store the dies in a clean, dry area.
Inspect die closure surfaces of the dies for worn,
cracked, or broken areas. If damage is evident, return
the die assembly to Tyco Electronics for evaluation
and repair. See Section 6, REPLACEMENT.
This inspection requires the use of a plug gage
conforming to the dimensions shown in Figure 5. Tyco
Electronics does not manufacture or market these
gages. To gage the crimping chamber, proceed as
follows:
1. Remove traces of oil or dirt from the crimping
chamber and plug gage.
2. Mate and adjust dies to meet the gage
dimension shown in Figure 6.
3. With dies positioned at the gage dimension,
align the GO element with the crimping chamber
(opposite side of part number markings). Push the
element (without forcing it) straight into the
Figure 4
Tyco Electronics recommends that a maintenance
and inspection program be performed periodically to
ensure dependable and uniform terminations. Though
recommendations call for at least one inspection a
month, frequency of inspection depends on:
1. The care, amount of use, and handling of the
die assembly.
2. The presence of abnormal amounts of dust and
dirt.
3. The degree of operator skill.
4. Your own established standards.
The die assembly is inspected before being shipped;
however, Tyco Electronics recommends that the die
assembly be inspected in accordance with Paragraph
5.2.B, Gaging the Crimping Chamber, immediately
upon arrival at your facility to ensure that the dies
have not been damaged during shipment.
chamber. The GO element must pass completely
through the first three laminations.
4. Align and try to insert the NO–GO element with
the same crimping chamber. The NO–GO element
may start entry but must not pass completely
through the crimping chamber.
If the crimping chamber conforms to the gage
inspection, the die assembly is considered
dimensionally correct. If not, the die assembly must
be replaced before returning it to service. See Section
6, REPLACEMENT.
If the die assembly is damaged or worn, it must be
replaced. Order replacement die assemblies through
your Tyco Electronics Representative, or call
1–800–526–5142, or send a facsimile of your
purchase order to 1–717–986–7605, or write to:
CUSTOMER SERVICE (38–35)
TYCO ELECTRONICS CORPORATION
P.O. BOX 3608
HARRISBURG, PA 17105–3608
相关PDF资料 |
PDF描述 |
|---|---|
| 69272-1 | TOOL HAND CRIMP STRATO-THERM |
| 69322-1 | TOOL HAND CRIMP SPLICE 10-12 AWG |
| 69331-1 | STR ACT DAHT COAXICON BNC |
| 69352 | HHHT TERMASHIELD SPLC 18-22AWG |
| 69357-3 | EXTRACT TOOL TERMI-POINT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 69255 | 制造商:FCI-CONNECTOR 制造商全称:FCI connector 功能描述:8 POS VERTICAL P.C.B. MOD JACK ASSY |
| 6925-5 | 制造商:Johanson Manufacturing 功能描述:TUNING ELEMENT |
| 69255-001 | 功能描述:以太网和电信连接器 PCB 8/8 VERTICAL RoHS:否 制造商:Pulse 产品:Modular Jacks 性能类别: USOC 代码:RJ45 位置/触点数量: 安装风格:Through Hole 端口数量:1 x 1 型式:Female 屏蔽: 电流额定值: 电压额定值: 触点电镀: 外壳材料:Thermoplastic IP 等级: |
| 69255-001LF | 功能描述:以太网和电信连接器 PCB 8/8 VERTICAL RoHS:否 制造商:Pulse 产品:Modular Jacks 性能类别: USOC 代码:RJ45 位置/触点数量: 安装风格:Through Hole 端口数量:1 x 1 型式:Female 屏蔽: 电流额定值: 电压额定值: 触点电镀: 外壳材料:Thermoplastic IP 等级: |
| 69255-001W | 功能描述:以太网和电信连接器 69255-001W-PCB MJ RoHS:否 制造商:Pulse 产品:Modular Jacks 性能类别: USOC 代码:RJ45 位置/触点数量: 安装风格:Through Hole 端口数量:1 x 1 型式:Female 屏蔽: 电流额定值: 电压额定值: 触点电镀: 外壳材料:Thermoplastic IP 等级: |
发布紧急采购，3分钟左右您将得到回复。