- 您现在的位置：买卖IC网 > Datasheet目录603 > 69734 (TE Connectivity)DIE PIDG STRATO 69710 #14 Datasheet资料下载
参数资料
| 型号： | 69734 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/11页 |
| 文件大小： | 0K |
| 描述： | DIE PIDG STRATO 69710 #14 |
| 标准包装： | 5 |
| 系列： | * |
408- 1632
PIDG Terminal,
PIDG STRATO- THERM
Terminal,
PLASTI- GRIP
Terminal, and
DIAMOND GRIP
Terminal
To Locate PIDG
STRATO--THERM
Terminal, Pull Locator
Down Slightly
Locator
NOTE The moving die must be removed from the die
holder to make this adjustment.
i
2. Insert the moving die into the die holder. Turn
the die holding screw enough to hold the die firmly
in place. DO NOT tighten the die holding screw at
this time.
3. Insert an UNSTRIPPED wire into ONLY the
insulation barrel of the terminal or splice.
Insulation Barrel
Section of Crimping
Chamber
PIDG Splice
Figure 6
Wire Barrel
Against Locator
Wire Barrel Section of
Crimping Chamber
4. Make a test crimp . Close the moving die on the
terminal or splice and hold the moving die in the
bottomed position. Tighten the die holding screw
while the dies are bottomed, then complete the
crimping cycle.
5. Remove the terminal or splice from the dies,
and check the insulation grip by bending the wire
back and forth ONCE. The terminal sleeve should
retain the grip on the wire insulation. If the wire
pulls out, set the insulation crimp adjustment to the
next tighter position as follows:
a. Remove the moving die from the die holder.
Window Indent Slid
Over and Down Into
Locator
Locator
b. Turn the lower insulation adjustment spacer
90 _ so that it fits between the moving die and
the die holder. Number 2 will appear on the
corner of the spacer.
c. Repeat the test crimp and adjust the moving
die as necessary until the desired insulation grip
is obtained.
6. With both adjustment spacers placed between
the moving die and the die holder, the die is set in
the tightest insulation crimping position. Number 1
will appear on the corner of the top spacer.
DIAMOND GRIP
Splice
Figure 7
4.2. PLASTI- GRIP Terminal
The insulation crimping section of the moving die has
three crimp positions: 1--Tight, 2--Medium, 3--Loose.
Adjust the insulation crimp as follows:
Window Indent Slid
Over Locator
NOTE
i
PLASTI--GRIP terminals feature a wire insulation
support only.
1.Use Position 3 for wire having a large insulation
diameter. Remove the moving die from the die
holder. Turn both insulation adjustment spacers so
that they fit into the notch in the side of the die.
See Figure 1.
Wire Barrel Against
Locator
4 of 11
Figure 8
Locator
2. Use Position 2 for wire having a medium
insulation diameter. Remove the moving die from
the die holder. Turn the lower insulation adjustment
spacer 90 _ so that it fits between the moving die
and the die holder. No. 2 will appear on the corner
of the spacer nearest the color code dot.
Rev C
相关PDF资料 |
PDF描述 |
|---|---|
| 69760 | ADAPTER SOLIS FLAG 69099 8-4/0 |
| 69814 | TOOL DIE BNC-TNC CRIMPING |
| 69815 | TOOL DIE BNC-TNC CRIMPING |
| 69872 | DIE PIDG 69875 22-16AWG |
| 69874 | TOOL DIE PIDG 69875 12-10AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 6973470001 | 制造商:TE Connectivity 功能描述:Cable Markers Cross Linked Polyolefin Black Pack 制造商:TE Connectivity 功能描述:TMS-SCE-1/4-2.0-0 - Cable Rools/Shrink Tubing |
| 69735 | 功能描述:冲压机与冲模 DIE ASSY 12-10 BLK RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 697-3800 | 制造商:ISOTECH 功能描述:Noise Dose Meter |
| 69738-001 | 制造商:FCI 功能描述:Conn Socket Strip F 60 POS 1.27mm Solder ST Edge Mount |
| 697381-000 | 制造商:TE Connectivity 功能描述:55 CABLE - Cable Rools/Shrink Tubing 制造商:TE Connectivity 功能描述:55PC1144-24-CML4-9CS2502 |
发布紧急采购，3分钟左右您将得到回复。