- 您现在的位置：买卖IC网 > PDF目录97839 > 71M6513-IGT/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | 71M6513-IGT/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封装： | LEAD FREE, LQFP-100 |
| 文件页数： | 48/104页 |
| 文件大小： | 1390K |
| 代理商： | 71M6513-IGT/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页当前第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页
71M6513/71M6513H
3-Phase Energy Meter IC
DATA SHEET
AUGUST 2011
Page: 48 of 104
2005-2011 Teridian Semiconductor Corporation
A Maxim Integrated Products Brand
out in 35 cycles and contains a leading flag bit. Figure 13 in the System Timing Section illustrates the RTM output format. RTM
is low when not in use.
SSI Interface: A high-speed serial interface with handshake capability is available to send a contiguous block of CE data to an
external data logger or DSP. The block of data, configurable as to location and size, is sent starting 1 cycle of 32kHz before
each CE code pass begins. If the block of data is big enough that transmission has not completed when the code pass begins,
it will complete during the CE code pass with no timing impact to the CE or the serial data. In this case, care must be taken
that the transmitted data is not modified unexpectedly by the CE. The SSI interface is enabled by the SSI_EN bit and consists
of SCLK, SSDATA, and SFR as outputs and, optionally, SRDY as input. The interface is compatible with 16bit and 32bit
processors. The operation of each pin is as follows:
SCLK is the serial clock. The clock can be 5MHz or 10MHz, as specified by the SSI_10M bit. The SSI_CKGATE bit controls
whether SCLK runs continuously or is gated off when no SSI activity is occurring. If SCLK is gated, it will begin 3 cycles before
SFR rises and will persist 3 cycles after the last data bit is output.
The pins used for the SSI are multiplexed with the LCD segment outputs, as shown in Table 58. Thus, the LCD should be
disabled when the SSI is in use.
SSI Signal
LCD Segment
Output Pin
SCLK
SEG3
SSDATA
SEG4
SFR
SEG5
SRDY
SEG6
Table 58: SSI Pin Assignment
SRDY is an optional handshake input that indicates that the DSP or data-logging device is ready to receive data. SRDY must
be true (the polarity of SRDY is selectable with SSI_FPOL) to enable SFR to rise and initiate the transfer of the next field. It is
expected that SRDY changes state on the rising edges of SCLK. If SRDY is not true when the SSI port is ready to transmit the
next field, transmission will be delayed until it is. SRDY is ignored except at the beginning of a field transmission. If SRDY is
not enabled (by SSI_RDYEN), the SSI port will behave as if SRDY is always true.
SSDATA is the serial output data. SSDATA changes on the rising edge of SCLK and outputs the contents of a block of CE
RAM words starting with address SSI_STRT and ending with SSI_END. The words are output MSB first.
The field size is set with the SSI_FSIZE register: 0 entire data block, 1-8 bit fields, 2-16 bit fields, 3-32 bit fields. The polarity of
the SFR pulse can be inverted with SSI_FPOL (SSI_FPOL = 0 SRDY high-active). If SRDY does not delay it, the first SFR
pulse in a frame will rise on the third SCLK after MUX_SYNC (or the fourth SCLK if 10MHz). MUX_SYNC can be used to
synchronize the fields arriving at the data logger or DSP.
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6515H-IGTW/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6515H-IGTWR/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6515H-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6515H-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 7234 | SPECIALTY ANALOG CIRCUIT, CDIP22 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6513-IGTR/F | 功能描述:计量片上系统 - SoC 3-Phase Energy Meter I/C RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6513-IGTR/F1 | 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6515H | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC |
| 71M6515H_11 | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Up to 10ppmC precision ultra-stable voltage reference Digital temperature compensation |
| 71M6515H-DB | 功能描述:开发板和工具包 - 8051 71M6515H Demo Brd RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。