收藏本站
参数资料
型号： 71M6534H-IGTR/F
厂商： TERIDIAN SEMICONDUCTOR CORP
元件分类： 模拟信号调理
英文描述： SPECIALTY ANALOG CIRCUIT, PQFP120
封装： LEAD FREE, LQFP-120
文件页数： 76/124页
文件大小： 2008K
代理商： 71M6534H-IGTR/F
FDS_6533_6534_004
71M6533/71M6534 Data Sheet
v1.1
2007-2009 TERIDIAN Semiconductor Corporation
55
2.3
Battery Modes
Shortly after system power (V3P3SYS) is applied, the part will be in MISSION mode. MISSION mode
means that the part is operating with system power and that the internal PLL is stable. This mode is the
normal operation mode where the part is capable of measuring energy.
When system power is not available (i.e. when V1<VBIAS), the 71M6533 and 71M6534 will be in one of
three battery modes: BROWNOUT, LCD, or SLEEP mode. Figure 20 shows a state diagram of the vari-
ous operation modes, with the possible transitions between modes. For information on the timing of
mode transitions refer to Figure 24 through Figure 26.
When V1 falls below VBIAS or the part wakes up under battery power, the part will automatically enter
BROWNOUT mode (see Section 2.5 Wake Up Behavior). From BROWNOUT mode, the part may enter
either LCD mode or SLEEP mode, as controlled by the MPU via the I/O RAM bits LCD_ONLY and SLEEP.
Figure 20: Operation Modes State Diagram
The transition from MISSION mode to BROWNOUT mode is signaled by the IE_PLLFALL interrupt flag
(SFR 0xE8[7]). The transition in the other direction is signaled by the IE_PLLRISE interrupt flag (SFR
0xE8[6]), when the PLL becomes stable.
Transitions from both LCD and SLEEP mode are initiated by wake-up timer timeout conditions or push-
button events. When the PB pin is pulled high (pushbutton is pressed), the IE_PB interrupt flag (SFR
0xE8[4]) is set, and when the wake-up timer times out, the IE_WAKE interrupt flag (SFR 0xE8[5]) is set.
In the absence of system power, if the voltage margin for the LDO regulator providing 2.5 V to the internal
circuitry becomes too low to be safe, the part automatically enters sleep mode (BAT_OK false). The battery
voltage must stay above 3 V to ensure that BAT_OK remains true. Under this condition, the 71M6533 and
71M6534 stays in SLEEP mode, even if the voltage margin for the LDO improves (BAT_OK true).
Table 45 shows the circuit functions available in each operating mode.
V3P3SYS
rises
V3P3SYS
falls
MISSION
BROWNOUT
LCD
SLEEP or
V1 > VBIAS
V1 <= VBIAS
LCD_ONLY
RESET &
VBAT_OK
RESET
IE_PLLRISE
IE_PLLFALL
IE_PB
IE_WAKE
PB
timer
PB
RESET &
V3P3SYS
rises
V3P3SYS
rises
VBAT_OK
SLEEP
相关PDF资料
PDF描述
71M6533-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6534-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP120
71M6533-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6534H-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP120
71M6533H-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
相关代理商/技术参数
参数描述
71M6534-IGT/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6534-IGTR/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6541D 制造商:未知厂家 制造商全称:未知厂家 功能描述:71M6541D/71M6541F/71M6541G/71M6542F/71M6542G 是 TeridianTM 的第4 代高集成度单相电表SoC
71M6541D_1111 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Energy Meter ICs
71M6541D-IGT/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*