- 您现在的位置：买卖IC网 > PDF目录68811 > 71M6542F-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | 71M6542F-IGTR/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封装： | LEAD FREE, LQFP-100 |
| 文件页数： | 112/165页 |
| 文件大小： | 2208K |
| 代理商： | 71M6542F-IGTR/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页当前第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页
50
2008–2011 Teridian Semiconductor Corporation
v1.1
2.5.1.2 MPU/CE RAM
The 71M6541D includes 3 KB of static RAM memory on-chip (XRAM) plus 256 bytes of internal RAM in
the MPU core. The 71M6541D/F and the 71M6542F include 5 KB of static RAM memory on-chip (XRAM)
plus 256 bytes of internal RAM in the MPU core. The static RAM is used for data storage for both MPU
and CE operations.
2.5.1.3 I/O RAM (Configuration RAM)
The I/O RAM can be seen as a series of hardware registers that control basic hardware functions. I/O
RAM address space starts at 0x2000. The registers of the I/O RAM are listed in Table 74.
The 71M6541D/F and 71M6542F include 128 bytes non-volatile RAM memory on-chip in the I/O RAM
address space (addresses 0x2800 to 0x287F). This memory section is supported by the voltage applied
at VBAT_RTC and the data in it are preserved in BRN, LCD, and SLP modes as long as the voltage at
VBAT_RTC is within specification.
2.5.2
Oscillator
The oscillator drives a standard 32.768 kHz watch crystal. This type of crystal is accurate and does not
require a high-current oscillator circuit. The oscillator has been designed specifically to handle watch
crystals and is compatible with their high impedance and limited power handling capability. The oscillator
power dissipation is very low to maximize the lifetime of any battery attached to VBAT_RTC.
Oscillator calibration can improve the accuracy of both the RTC and metering. Refer to 2.5.4, Real-Time
Clock (RTC) for more information.
The oscillator is powered from the V3P3SYS pin or from the VBAT_RTC pin, depending on the V3OK
internal bit (i.e., V3OK = 1 if V3P3SYS
≥ 2.8 VDC and V3OK = 0 if V3P3SYS < 2.8 VDC). The oscillator
requires approximately 100 nA, which is negligible compared to the internal leakage of a battery.
2.5.3
PLL and Internal Clocks
Timing for the device is derived from the 32.768 kHz crystal oscillator output that is multiplied by a PLL by
600 to produce 19.660800 MHz, the master clock (MCK). All on-chip timing, except for the RTC clock, is
derived from MCK. Table 41 provides a summary of the clock functions and their controls.
The two general-purpose counter/timers contained in the MPU are controlled by CKMPU (see 2.4.6
The master clock can be boosted to 19.66 MHz by setting the PLL_FAST bit = 1 (I/O RAM 0x2200[4]) and
can be reduced to 6.29 MHz by PLL_FAST = 0. The MPU clock frequency CKMPU is determined by
another divider controlled by the I/O RAM control field MPU_DIV[2:0] (I/O RAM 0x2200[2:0]) and can be
set to MCK*2
-(MPU_DIV+2) , where MPU_DIV[2:0] may vary from 0 to 4. The 71M654x V3P3SYS supply
current is reduced by reducing the MPU clock frequency. When the ICE_E pin is high, the circuit also
generates the 9.83 MHz clock for use by the emulator.
The PLL is only turned off in SLP mode or in LCD mode when LCD_BSTE is disabled. The LCD_BSTE
value depends on the setting of the LCD_VMODE [1:0] field (see Table 56).
When the part is waking up from SLP or LCD modes, the PLL is turned on in 6.29 MHz mode, and the PLL
frequency is not be accurate until the PLL_OK flag (SFR 0xF9[4]) rises. Due to potential overshoot, the MPU
should not change the value of PLL_FAST until PLL_OK is true.
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6541D-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6542G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6541G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6541F-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6543F-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6542FT-IGT/F | 制造商:Maxim Integrated Products 功能描述:1-PHASE SOC 128KB WITH PREC TEMP SENSOR - Rail/Tube |
| 71M6542FT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:1-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel |
| 71M6542G | 制造商:未知厂家 制造商全称:未知厂家 功能描述:71M6541D/71M6541F/71M6541G/71M6542F/71M6542G 是 TeridianTM 的第4 代高集成度单相电表SoC |
| 71M6542G-IGT/F | 功能描述:计量片上系统 - SoC 1-Phase Metering SOC with 128KB Flash RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6542G-IGTR/F | 制造商:Maxim Integrated Products 功能描述:- Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。