参数资料
型号: 73M1822-KEYCHN
厂商: Maxim Integrated Products
文件页数: 62/82页
文件大小: 0K
描述: BOARD KEYCHAIN 73M1822 42-QFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 1
主要目的: *
嵌入式: *
已用 IC / 零件: *
主要属性: *
次要属性: *
已供物品: 板,CD
DS_1x22_017
73M1822/73M1922 Data Sheet
Rev. 1.6
65
11.5 Trans-Hybrid Cancellation
A Transmit Bit Stream (TBS) emulating a sinusoid of 1 kHz, full scale (code word of +/- 32,767) is applied to
SDIN and the residual signal is measured at SDOUT. Unless stated otherwise, test conditions are: ACZ=00
(600 Ω termination), THEN=1, ATEN=0, DAA=01, TXBST=0. TXM is externally fed back into the Line-Side
Device (73M1912) to effect cancellation of transmit signal.
Table 43: Trans-Hybrid Cancellation
Parameter
Test Condition
Min
Nom
Max
Units
Transmit hybrid
cancellation
Measure RxD in HIC
26
dB
Offset voltage
50% 1’s Density
25
50
mV
AC swing
1kHz sinusoid at Tip and Ring
0.85
0.95
1.05
Vpk
Idle noise
300 Hz – 4 kHz at Tip and Ring
-81
dBm
11.6 Direct Access Arrangement Control Functions
These Transmit Control Registers contain control information to set up the line side of the 73M1x22.
Included are DC-IV characteristics, off-hook control, etc.
Table 44: DAA Control Functions
Function
Mnemonic
Register
Location
Type
Description
OFH
0x12[7]
WO
Off-Hook Enable
This bit controls the state of the Hook signal.
0 = On-Hook. (Default)
1 = Off-Hook.
PLDM
0x13[3]
WO
Pulse Dialing Mode Enable
Alleviates the strict timing requirements for the Host having to control
ENDC and OFH during pulse dialing. With PLDM = 1, the Host only has
to toggle OFH to perform pulse dialing.
0 = Pulse Dialing Mode is disabled. (Default)
1 = Pulse Dialing Mode is enabled.
IDISPD
0x13[1:0]
WO
Discharge and Pulse Dialing
Controls the DC discharge current and how fast the loop turns off. Affects
pulse dialing waveform. Controls the amount of discharge current during
hook switch transitions.
0 = Minimum current. (Default)
1 = Maximum current.
It is recommended to set IDISPD to 1 prior to hook switching operations.
ENNOM
0x12[0]
WO
Enable Nominal Operation
0 = Speeds up the on and off hook transitions time by increasing the DC
loop bandwidth of the DC transconductance circuit in the 73M1x22. This
can be used for pulse dialing. In addition, ENNOM=0 prevents the reset
of all bits in Register 0x12. (Default)
1 = Enter Nominal Operation. Reduces the loop bandwidth of the DC
transconductance circuit. Allows reset of Register 0x12 caused by bits
UVDT, OVDT or OIDT.
相关PDF资料
PDF描述
78Q2133-DB EVAL BOARD 78Q2133
MAX14821EVKIT# EVAL KIT MAX14821
UVZ1C472MHD CAP ALUM 4700UF 16V 20% RADIAL
78Q2123-DB BOARD DEMO 78Q2123 78Q2133
78Q2120C09-DB BOARD DEMO 78Q2120C
相关代理商/技术参数
参数描述
73M1866B-IFX 功能描述:电信线路管理 IC MicroDAA w/PCM Highway RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray
73M1866B-IM/F 功能描述:电信线路管理 IC MicroDAA w/PCM Highway RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray
73M1866B-IMR/F 功能描述:电信线路管理 IC MicroDAA w/PCM Highway RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray
73M1866B-KEYCHN 功能描述:网络开发工具 73M1866B Keychain Brd RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V
73M1902-IM/F 功能描述:电信线路管理 IC MicroDAA Chip Set Host Side RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray