- 您现在的位置：买卖IC网 > PDF目录68812 > 73M1903-IGV (TERIDIAN SEMICONDUCTOR CORP) SPECIALTY CONSUMER CIRCUIT, PQFP32 PDF资料下载
参数资料
| 型号： | 73M1903-IGV |
| 厂商： | TERIDIAN SEMICONDUCTOR CORP |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP32 |
| 封装： | TQFP-32 |
| 文件页数： | 42/45页 |
| 文件大小： | 449K |
| 代理商： | 73M1903-IGV |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页当前第42页第43页第44页第45页
73M1903
Modem Analog Front End
DATA SHEET
ge: 6 of 45
2005 TERIDIAN Semiconductor Corporation
Rev 1.4
SERIAL INTERFACE
The serial data port is a bi-directional port that can be supported by most DSPs. Although the 73M1903
is a peripheral to the DSP (host controller), the 73M1903 is the master of the serial port. It generates a
serial bit clock, Sclk, from a system clock, Sysclk, which is normally an output from an on-chip PLL that
can be programmed by the user. The serial bit clock is always derived by dividing the system clock by 18.
The sclk rate, Fsclk, is related to the frame synchronization rate, Fs, by the relationship Fsclk = 256 x Fs
or Fs = Fsclk / 256 = Fsys / 18 / 256 = Fsys / 4608, where Fsys is the frequency of Sysclk. Fs is also the
rate at which both the transmit and receive data bytes are sent (received) to (by) the Host. Throughout
this document two pairs of sample rate, Fs, and crystal frequency, Fxtal, will be often cited to facilitate
discussions. They are:
1. Fxtal1 = 27MHz, Fs1 = 7.2kHz
2. Fxtal2 = 18.432MHz, Fs2 = 8kHz.
3. Fxtal3 = 24.576MHz, Fs3 = 9.6kHz – chip default.
Upon reset, until a switch to the PLL based clock, Pllclk, occurs, the system clock will be at the crystal
frequency, Fxtal, and therefore the serial bit clock will be sclk = Fsys/18 = Fxtal/18.
Examples:
1. If Fxtal1 = 27.000MHz, then sclk=1.500MHz and Fs=sclk/256 = 5.859375kHz.
2. If Fxtal2 = 18.432MHz, then sclk=1.024MHz and Fs=sclk/256 = 4.00kHz.
3. If Fxtal3 = 24.576MHz, then sclk=1.3653MHz and Fs=sclk/256 = 5.33kHz.
When 73M1903 is programmed through the serial port to a desired Fs and the PLL has settled out, the
system clock will transition to the PLL-based clock in a glitch-less manner.
Examples:
1. If Fs1 = 7.2kHz, Fsys = 4608 * Fs = 33.1776MHz and sclk = Fsys / 18 = 1.8432MHz.
2. If Fs2 = 8.0kHz, Fsys = 4608 * Fs = 36.8640MHz and sclk = Fsys / 18 = 2.048MHz.
3. If Fs3 = 9.6kHz, Fsys = 4608 * Fs = 44.2368MHz and sclk = Fsys / 18 = 2.4576MHz.
This transition is entirely controlled by the host. Upon reset or power down of PLL and/or analog front
end, the chip will automatically run off the crystal until the host forces the transition by setting a bit in a
designated serial port register – location bit 7, 0Eh. The transition should be forced on or after the
second Frame Synch period following the write to a designated PLL programming register (0Dh).
When reprogramming the PLL the host should first transition the system clock to the crystal before
reprogramming the PLL so that any transients associated with it will not adversely impact the serial port
communication.
Power saving is accomplished by disabling the analog front end by clearing bit 7 of CTRL1 (address 00h),
ENFE=0.
During the normal operation, a data
FS is generated by the 1903 at the rate of Fs. For every data FSB
there are 16 bits transmitted and 16 bits received. The frame synchronization (
FS) signal is pin
programmable for type.
FS can either be early or late determined by the state of the TYPE input pin.
When Type pin is left open, an early
FS is generated in the bit clock prior to the first data bit transmitted
相关PDF资料 |
PDF描述 |
|---|---|
| 73M1903-IM | SPECIALTY CONSUMER CIRCUIT, QCC32 |
| 73M1903-IGV/F | SPECIALTY CONSUMER CIRCUIT, PQFP32 |
| 73M1903-IGV | SPECIALTY CONSUMER CIRCUIT, PQFP32 |
| 73M1903-IM | SPECIALTY CONSUMER CIRCUIT, QCC32 |
| 73M1903-IM/F | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 73M1903-IM/F | 功能描述:电信线路管理 IC Modem AFE V.22Bis-V.92 RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| 73M1903-IM/F1 | 功能描述:电信线路管理 IC RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| 73M1903-IMR/F | 功能描述:电信线路管理 IC Modem AFE V.22Bis-V.92 RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| 73M1903-IMR/F1 | 功能描述:电信线路管理 IC RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| 73M1903-IVT/F | 功能描述:IC MODEM AFE V.22BIS 20-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模拟前端 (AFE) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:- 通道数:2 功率（瓦特）:- 电压 - 电源，模拟:3 V ~ 3.6 V 电压 - 电源，数字:3 V ~ 3.6 V 封装/外壳:32-VFQFN 裸露焊盘 供应商设备封装:32-QFN（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。