参数资料
| 型号： | 73S8009CN-DB |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/30页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO FOR 73S8009CN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
73S8009CN Data Sheet
DS_8009CN_026
Pin
Name
CLK
Pin
Number
16
Type
O
Equivalent
Circuit
Description
Card clock: provides clock signal (CLK) to card. CLK
is the pass through of the signal on pin CLKIN.
Internal control logic will hold CLK low when card is
not activated or VCC is too low. Will be tri-stated
when SC/ USB is set low.
PRES
14
I
Smart card Presence switch: Active high indicates
card is present.
Smart card activation will not be permitted unless
PRES is active.
VCC
19
PSO
Card power supply – logically controlled by
sequencer, output of LDO regulator. Requires an
external 0.47uF low ESR filter capacitor to GND.
GND
17
GND
–
Card ground.
Host Processor Interface
CS
12
I
Chip Select. When CS = 1, the control and signal
pins are configured normally. When CS is set low,
CMDVCC% , RSTIN, and CMDVCC# are latched.
I/OUC, AUX1UC, and AUX2UC are set to
high-impedance pull-up mode and do not pass data
to or from the smart card. Signals RDY and OFF are
disabled to prevent a low output and the internal
pull-up resistors are disconnected. Should be tied to
VDD when a single 73S8009CN is used.
OFF
32
O
Interrupt signal to the processor. Active Low -
Multi-function indicating fault conditions and card
presence. Open drain output configuration – It
includes an internal 20kΩ pull -up to V DD. Pull-up is
disabled in Power down state and CS = 0 modes.
I/OUC
AUX1UC
1
2
IO
IO
System controller data I/O to/from the card. Includes
an 11kΩ pull -up resistor to V DD.
System controller auxiliary data I/O to/from the card
for synchronous / asynchronous operation mode.
Connection to AUX1 is opened when SC/ USB is low.
Includes an 11kΩ pull -up resistor to V DD.
AUX2UC
3
IO
System controller auxiliary data I/O to/from the card
for synchronous / asynchronous operation mode.
Connection to AUX2 is opened when SC/ USB is low.
Includes an 11kΩ pull -up resistor to V DD.
SC/ USB
13
I
Smart Card Interface enable, USB interface disable.
Pin is provided with a weak pull-up.
When high, the 73S8009CN operates in
synchronous / asynchronous operation mode.
When low, CLK, RST I/O, AUX1, and AUX2 are
tri-stated. Pin AUX1 is connected to pin DP and pin
AUX2 is connected to pin DM.
DP
25
IO
USB D+ connection to / from USB controller.
When SC/ USB is set low, this pin is electrically
connected to the AUX1 pin, otherwise it is isolated.
6
Rev. 1.4
相关PDF资料 |
PDF描述 |
|---|---|
| 73S8009R-DB | BOARD DEMO 73S8009R 28-SOIC |
| 73S8014RT-DB | BOARD DEMO 73S8010RT 20-SOIC |
| 74-1/4"X72YD | TAPE ELECTRICAL POLY 1/4" YEL |
| 74032-103LF | USB A TYPE PLUG KIT LF |
| 74056-0010BLF | UNIV SERIAL BUS T/H LF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 73S8009R | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Low Cost Versatile Smart Card Interface |
| 73S8009R-DB | 功能描述:界面开发工具 73S8009R Demo Brd RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| 73S8009R-IL/F | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface IC RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8009R-ILR/F | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface IC RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8009R-IM/F | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface IC RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。