- 您现在的位置：买卖IC网 > PDF目录97839 > 73S8009R-IL/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PDSO28 PDF资料下载
参数资料
| 型号： | 73S8009R-IL/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 封装： | LEAD FREE, SOP-28 |
| 文件页数： | 6/23页 |
| 文件大小： | 342K |
| 代理商： | 73S8009R-IL/F |
73S8009R Data Sheet
DS_8009R_056
14
Rev. 1.3
3.2
System Controller Interface
Four separate digital inputs allow direct control of the card interface from the host as follows:
Pin CS: Enables the system controller interface.
Pin
CMDVCC# and/or CMDVCC%: When low, starts an activation sequence.
Pin RSTIN: Controls the card Reset signal (when enabled by the sequencer).
Other functions are controlled as follows:
PWRDN places the 73S8009R in a low power mode and shuts down all functions.
The card clock is completely controlled by CLKIN.
Vcc output voltage valid is indicated on the RDY pin.
Interrupt output to the host: As long as the card is not activated, the
OFF pin informs the host about
the card presence only (low = no card in the reader).
When
CMDVCC is set low (Card activation sequence requested from the host), a low level on OFF
means a fault has been detected (e.g. card removal during card session, or voltage fault, or thermal /
over-current fault). This condition automatically initiates a deactivation sequence.
3.3
Power Supply and Voltage Supervision
The Teridian 73S8009R smart card interface IC incorporates a LDO voltage regulator. The voltage
output is controlled by the digital input sequence on
CMDVCC# and CMDVCC%. This regulator is able to
provide either 1.8 V, 3 V or 5 V card voltages from the power supply applied on the VPC pin.
Digital circuitry is powered by the power supply applied on the VDD pin. VDD also defines the voltage
range to interface with the system controller.
Three voltage supervisors constantly check the presence of the voltages VDD, VPC and VCC. A card
deactivation sequence is forced upon a fault detected by any of these voltage supervisors.
The voltage regulator can provide a card current of 65 mA in compliance with EMV 4.1, and of at least
90 mA in compliance with ISO7816-3. The VCC voltage supervisor threshold values are defined from the
EMV standard.
3.4
Card Power Supply
The card power supply is internally provided by the LDO regulator. The signals
CMDVCC# and
CMDVCC% control the turn-on, output voltage value, and turn-off of V
CC. When either signal is asserted
low, VCC will ramp to the selected value or if both signals are asserted low (within 400 ns of each other),
VCC will ramp to 1.8 volts. These signals are edge triggered. If CMDVCC% is asserted low (to command
VCC to be 5 V) and at a much later time (greater than 2 s, typically), CMDVCC# is asserted low, it will be
ignored (and vice versa).
At the assertion (low) of either or both
CMDVCC#/CMDVCC% signals, V
CC will rise to the requested value.
When VCC rises to an acceptable value, and stays above that value for approximately 20 s, RDY will be
set high. Approximately 510 s after the fall of
CMDVCC#/CMDVCC% the circuit will check the see if V
CC
is at or above the required minimum value (indicated by RDY=1) and if not, will begin an emergency
deactivation sequence. During the 510 s time, over-temperature, card removal, or de-assertion of
CMDVCC#/CMDVCC% shall also initiate an emergency deactivation sequence.
相关PDF资料 |
PDF描述 |
|---|---|
| 73S8009R-IMR/F | SPECIALTY ANALOG CIRCUIT, QCC20 |
| 73S8014R-ILR/F | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 73S8014R-IL/F | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 73S8014RT-ILR/F | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 73S8014RT-IL/F | SPECIALTY ANALOG CIRCUIT, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 73S8009R-ILR/F | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface IC RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8009R-IM/F | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface IC RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8009R-IMR/F | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface IC RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8010C | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Smart Card Interface |
| 73S8010C-DB | 功能描述:界面开发工具 73S8010C Demo Brd RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。