参数资料
| 型号： | 74AHC241PW,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 13/15页 |
| 文件大小： | 0K |
| 描述： | IC BUFFER/LINEDVR 3ST TSSOP20 |
| 标准包装： | 1 |
| 系列： | 74AHC |
| 逻辑类型： | 缓冲器/线路驱动器，非反相 |
| 元件数： | 2 |
| 每个元件的位元数： | 4 |
| 输出电流高，低： | 8mA，8mA |
| 电源电压： | 2 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 标准包装 |
| 其它名称： | 568-5240-6 |
74AHC_AHCT241_1
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 01 — 11 January 2010
7 of 15
NXP Semiconductors
74AHC241; 74AHCT241
Octal buffer/line driver; 3-state
[1]
Typical values are measured at nominal supply voltage (VCC = 3.3 V and VCC = 5.0 V).
[2]
tpd is the same as tPLH and tPHL; ten is the same as tPZH and tPZL; tdis is the same as tPLZ and tPHZ.
[3]
CPD is used to determine the dynamic power dissipation (PD in μW).
PD = CPD × VCC2 × fi × N + ∑(CL × VCC2 × fo) where:
fi = input frequency in MHz;
fo = output frequency in MHz;
CL = output load capacitance in pF;
VCC = supply voltage in V;
N = number of inputs switching;
∑(C
L × VCC
2
× f
o) = sum of outputs.
11. Waveforms
ten
enable time
1OE to 1Yn; see Figure 6
VCC = 4.5 V to 5.5 V; CL = 15 pF
-
3.7
6.6
1.0
7.8
9.2
ns
VCC = 4.5 V to 5.5 V; CL = 50 pF
-
5.4
9.5
1.0
11.1
12.4
ns
2OE to 2Yn; see Figure 7
VCC = 4.5 V to 5.5 V; CL = 15 pF
-
3.7
6.6
1.0
7.8
9.2
ns
VCC = 4.5 V to 5.5 V; CL = 50 pF
-
5.4
9.5
1.0
11.1
12.4
ns
tdis
disable time
1OE to 1Yn; see Figure 6
VCC = 4.5 V to 5.5 V; CL = 15 pF
-
4.8
7.8
1.0
8.8
9.7
ns
VCC = 4.5 V to 5.5 V; CL = 50 pF
-
7.1
10.5
1.0
11.4
13.5
ns
2OE to 2Yn; see Figure 7
VCC = 4.5 V to 5.5 V; CL = 15 pF
-
4.8
7.8
1.0
8.8
9.7
ns
VCC = 4.5 V to 5.5 V; CL = 50 pF
-
7.1
10.5
1.0
11.4
13.5
ns
CPD
power
dissipation
capacitance
VI = GND to VCC; CL = 50 pF;
fi = 1 MHz
-
9
-
pF
Table 7.
Dynamic characteristics …continued
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8.
Symbol Parameter
Conditions
25
°C
40 °C to +125 °C
Unit
Min
Typ[1]
Max
Min
Max
(85
°C)
Max
(125
°C)
Measurement points are given in Table 8.
VOL and VOH are typical voltage output drop that occur with the output load.
Fig 5.
Propagation delay input (nAn) to output (nYn)
mgu781
nAn input
nYn output
tPHL
tPLH
GND
VI
VM
VOH
VOL
相关PDF资料 |
PDF描述 |
|---|---|
| VI-242-MV-F1 | CONVERTER MOD DC/DC 15V 150W |
| MS27467T17B99SBLC | CONN HSG PLUG 23POS STRGHT SCKT |
| VI-241-MV-F4 | CONVERTER MOD DC/DC 12V 150W |
| NDXD2412C | CONV DC/DC 7.5W 24VIN 12VOUT DIP |
| MS3456W22-2SLC | CONN HSG PLUG 3POS STRGHT SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 74AHC244 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Octal buffer/line driver; 3-state |
| 74AHC244BQ | 制造商:NXP Semiconductors 功能描述:IC BUFFER/DRIVER TRI-ST VQFN |
| 74AHC244BQ,115 | 功能描述:缓冲器和线路驱动器 OCTAL BUFFER 3-STATE RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| 74AHC244BQ-G | 功能描述:缓冲器和线路驱动器 OCTAL BUFFER 3-STATE RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| 74AHC244BQ-Q100,11 | 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 8-CH Non-Inverting 3-ST CMOS 20-Pin DHVQFN EP T/R 制造商:NXP Semiconductors 功能描述:74AHC244BQ-Q100/DHVQFN20/REEL7 - Tape and Reel 制造商:NXP Semiconductors 功能描述:IC BUFFER LINE DVR OCT 20DHVQFN |
发布紧急采购，3分钟左右您将得到回复。