Philips Semiconductors
Product specification
74LV4799
Timer for NiCd and NiMH chargers
1998 Apr 20
7
RECOMMENDED OPERATING CONDITIONS
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
VCC
DC supply voltage
See Note 1
0.9
1.2
6
V
VI
Input voltage pins 4, 5, and 9
Input voltage pins 7, 13, 14, and 15
0
–
10
VCC
V
VO
Output voltage pins 10, 11, and 12
Output voltage pins 1, 2, 3, and 6
0
–
VCC
10
V
Tamb
Operating ambient temperature range in free air
See DC and AC
characteristics per device
0
+70
°C
Input rise and fall times pin 5
–
10
ms
tr, tf
Input rise and fall times pins 7, 14 and 15
VCC = 1.0V; VI = 1.0V
VCC = 2.0V; VI = 2.0V
VCC = 3.0V; VI = 4.5V
VCC = 3.6V; VI = 6.0V
–
500
200
100
50
ns
Input rise and fall times pin 9
–
2
s
NOTE:
1. Single sided input protection applied on pins 4, 5, and 9.
ABSOLUTE MAXIMUM RATINGS2, 3
In accordance with the Absolute Maximum Rating System (IEC 134).
Voltages are referenced to GND (ground = 0 V).
SYMBOL
PARAMETER
CONDITIONS
MIN
MAX
UNIT
VCC
DC supply voltage
–0.5
+7.0
V
DC input diode current pins 4, 5 and 9
VI < –0.5 or VI > 12 V
±20
IIK
DC input diode current pins 7, 13, 14 and 15
VI < –0.5 or VI > VCC + 0.5 V
+20
mA
NON repetitive peak DC input diode current pin 9
VI > 10 V and t < 10 ms; see note 1
10
VI
DC input voltage range pins 4, 5 and 9
–0.5
+12
V
VI
DC input voltage range pins 7, 13, 14 and 15
–0.5
VCC + 0.5
V
IOK
DC output diode current pins 1, 2, 3 and 6
VO < –0.5 V
–20
mA
IO
DC output sink current pins 1, 2, 3 and 6
VO > 0 V
–25
mA
IOK
DC output diode current pins 10, 11 and 12
VO < –0.5 or VO > VCC + 0.5 V
±20
mA
IO
DC output sink or source current pins 10, 11 and 12
–0.5 V
< VO < VCC + 0.5 V
±25
mA
IGND, ICC
DC GND or VCC current
±50
mA
Tstg
Storage temperature range
–65
+150
°C
Power dissipation per package
for temperature range: –40 to +125
°C
Ptt
Power dissi ation er ackage
Plastic DIL
for tem erature range: 40 to +125 C
above + 70
°C derate linearly with 12 mW/K
750
mW
Ptot
Plastic mini-pack (SO)
Pl
ti
h i k
i i
k (SSOP
d TSSOP)
y
above + 70
°C derate linearly with 8 mW/K
b60
°C d
t li
l
ith 5 5
W/K
500
400
mW
Plastic shrink mini-pack (SSOP and TSSOP)
above + 60
°C derate linearly with 5.5 mW/K
400
NOTES:
1. In applications where a motor is present, the input voltage may exceed the maximum VI, level of 10 V at the DIS input for a very short period
when the motor is switched off.
2. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the
device at these or any other conditions beyond those under “recommended operating conditions” is not implied. Exposure to absolute
maximum rated conditions for extended periods may affect device reliability.
3. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.