- 您现在的位置：买卖IC网 > PDF目录369340 > 7525 (Toshiba Corporation) X-ray Thickness Gage PDF资料下载
参数资料
| 型号： | 7525 |
| 厂商： | Toshiba Corporation |
| 英文描述： | X-ray Thickness Gage |
| 中文描述： | X射线测厚仪 |
| 文件页数： | 8/14页 |
| 文件大小： | 204K |
| 代理商： | 7525 |
No. EJD-069
8
Profile Measurement Specifications
1.
Measurement Mode
Item
Scanning Pattern
Standard Specifications
Full-width profile
scanning
WS
DS
In this mode the carriage is made to scan in a strip
width direction by a start profile measurement
command, thereby measuring the whole width profile.
The speed of the carriage is 30mm/s on both edges,
and 100mm/s at the center.
Edge profile
scanning
WS
DS
In this mode the carriage is made to scan in a strip
width direction by a start profile measurement
command, thereby measuring the edge profile.
WS (or DS) edge distance is set beforehand fromthe
customer's computer.
Center
measurement
WS
DS
This mode measures the center of the strip
continuously in a longitudinal direction.
It is used as backup for AGC thickness gages (center
measurement).
2.
Data Processing
The profile data processing shown below is carried out, and it is displayed on the operation-PC.
’’
’’
’’
’
’
’
’
’’
’
’’
Figure 4 Section in Strip Width Direction
1)
Crown Value
Crown value, WS crown value, DS crown value are calculated
from the measurements of center plate thickness, WS side
specified measurement points and DS side specified
measurement points.
Crown values are calculated as follows:
a)
Crown value: chi = hc- (hi' + hi'')/2
b)
WS crown value: chi' = hc-hi'
c)
DS crown value: chi' = hc-hi''
2)
Wedge Value
Wedge value is calculated from the measured thickness at WS
side specified measurement points and DS side specified
measurement points.
The formula for calculation is shown below.
Whi = hi''
–
hi'
Line flow direction
Edge distance
Line center
Note:
a. Edge distance settings i', i'', and j', j'' are the same.
b. i can be set from 5 to 50mm
(i can be set at 5 locations)
c. j can be set from 50 to 100mm
(edge drop standard)
d. i < j (in these specifications the initial settings are i
= 25mm, j = 75mm.)
3)
Edge Drop Amount
Edge drop amount is calculated
from the measured width between
two points specified on the WS side
and DS side.
Calculations are made as follows.
a)
WS edge drop amount:
eh' = hj'
–
hi'
b)
DS edge drop amount:
eh'' = hj''
–
hi''
相关PDF资料 |
PDF描述 |
|---|---|
| 7528AC | 4-Bit, Single-Chip CMOS Microcomputers With FIP Driver |
| 75323 | LINEAR INTEGRATED CIRCUIT |
| 75415-EP | POWER GOOD FAST-TRANSIENT-RESPONSE 2-A LOW-DROPOUT VOLTAGE REGULATORS |
| 75418-EP | POWER GOOD FAST-TRANSIENT-RESPONSE 2-A LOW-DROPOUT VOLTAGE REGULATORS |
| 75425-EP | POWER GOOD FAST-TRANSIENT-RESPONSE 2-A LOW-DROPOUT VOLTAGE REGULATORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 75-250 | 制造商:THORDARSON MEISSNER 功能描述:Power Supply,Foreign,Portable,in:100/120/220/240V,50/60HZ,out:120V,250VA 制造商:Datak Corporation 功能描述:Connector Accessories Double Gang Wall Plate Cover Straight Ivory |
| 7525-001/230AC | 制造商:Redington Counters Inc 功能描述: |
| 75250201151 | 制造商:ESSEX 功能描述:25AMP RELAY COIL 240V 60HZ |
| 7525070001 | 制造商:TE Connectivity 功能描述:Heat Shrink Sleeve ST Polyolefin Yellow 制造商:TE Connectivity 功能描述:MARKER SLEEVE POLYFN YLLW - Cable Rools/Shrink Tubing |
| 752511 | 制造商: 功能描述: |
发布紧急采购，3分钟左右您将得到回复。