- 您现在的位置：买卖IC网 > PDF目录20611 > 78M6612-MR/F/P2 (Maxim Integrated)IC PWR MEASUREMENT AC 68SQFN PDF资料下载
参数资料
| 型号： | 78M6612-MR/F/P2 |
| 厂商： | Maxim Integrated |
| 文件页数： | 25/46页 |
| 文件大小： | 0K |
| 描述： | IC PWR MEASUREMENT AC 68SQFN |
| 标准包装： | 250 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
DS_6612_001
78M6612 Data Sheet
3.9
UART1 (TX1/RX1)
The TX1 and RX1 pins can be used for a regular serial interface (by connecting a RS-232 transceiver for
example), or they can be used to directly operate optical components (for example, an infrared diode and
phototransistor implementing a FLAG interface).
3.10 Connecting V1 and Reset Pins
A voltage divider should be used to establish that V1 is in a safe range (see Figure 15) . V1 must be
lower than 2.9 V in all cases in order to keep the hardware watchdog timer enabled. A series 5 k ?
resistor (R3) and a capacitor to ground (C1) are added for enhanced EMC immunity. The parallel
impedance of R1 and R2 should be approximately 8 k ? to 10 k ? in order to provide hysteresis for the
power fault monitor.
V3P3
R 1
R 3
GND
R 2
5k Ω
C 1
100pF
V1
Figure 15: Voltage Divider for V1
Even though a functional power and measurement unit will not necessarily need a reset switch, it is useful to
have a reset pushbutton switch for prototyping, as shown in Figure 16 , left side. The RESET signal may be
sourced from V3P3SYS, or VBAT (if a battery is present), or from a combination of these sources, depending
on the application.
For production, the RESET pin should be protected by the external components shown in Figure 16 , right
side. R 1 should be in the range of 100 ? and mounted as closely as possible to the IC. The RESET pin
can also be directly connected to ground.
VBAT/
V3P3D
R 2
V3P3D
78M6612
78M6612
1k Ω
Reset
Switc
h
1nF
10k Ω
R 1
RESE
T
DGN
D
100 Ω
R 1
RESET
DGND
Figure 16: External Components for RESET: Development Circuit (Left), Production Circuit (Right)
Rev 2
25
相关PDF资料 |
PDF描述 |
|---|---|
| 78M6613-IM/F | IC AC PWR MON APPLIANCES 32-QFN |
| ECC12DCSN-S288 | CONN EDGECARD 24POS .100 EXTEND |
| RBA06DTKI-S288 | CONN EDGECARD 12POS .125 EXTEND |
| FIN4.00RD25 | FIREFLEX FIBERGLASS 4" RED 25' |
| 71M6511H-IGT/F | IC ENERGY METER RESIDENT 64-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 78M6612-SOCKET64 | 功能描述:计量片上系统 - SoC 78M6612 64PIN LQFP PROGRAM BOARD RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 78M6612-SOCKET68 | 功能描述:计量片上系统 - SoC 78M6612 68PIN QFN PROGRAM BOARD RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 78M6612SP-EVM-1 | 功能描述:开发板和工具包 - 8051 78M6612 Eval Kit RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
| 78M6613 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Four Sensor Inputs—V3P3A Referenced 32KB Flash with Security |
| 78M6613_12 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single-Phase AC Power Measurement IC |
发布紧急采购，3分钟左右您将得到回复。