- 您现在的位置：买卖IC网 > PDF目录378256 > 8905 (Allegro MicroSystems, Inc.) 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING PDF资料下载
参数资料
| 型号： | 8905 |
| 厂商： | Allegro MicroSystems, Inc. |
| 英文描述： | 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING |
| 中文描述： | 3相无刷直流电动机控制器/驱动器，反电动势遥感 |
| 文件页数： | 8/12页 |
| 文件大小： | 163K |
| 代理商： | 8905 |
8905
3-PHASE BRUSHLESS DC
MOTOR CONTROLLER/DRIVER
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
A once-per-revolution TACH signal can be
generated by counting cycles of FCOM (the
number of motor poles must be selected via the
serial port). TACH is then a jitter-free signal that
toggles once per motor revolution. The rising
edge of TACH triggers REF, a precision speed
reference derived by a programmable counter.
The duration of REF is set by programming the
counter to count the desired number of OSC
cycles
desired
total count
=
where the total count (number of oscillator cycles)
is equal to the sum of the selected (programmed
low) count numbers corresponding to bits D5
through D18.
The speed error is detected as the difference
in falling edges of TACH and REF. The speed
error signals control the error-correcting charge
pump on the FILTER terminal, which drive the
external loop compensation components to correct
the motor current.
Index.
An external tachometer signal may be
used to create the TACH signal, rather than the
internally derived once around. To use this mode,
the signal is input to the INDEX terminal, and the
index mode must be enabled via the serial port.
When Switching from the once-around mode to
index mode, it is important to monitor the SYNC
signal on DATA OUT, and switch modes only
when SYNC is low. This ensures making the
transition without disturbing the speed control
loop. The speed reference counter should be
reprogrammed at the same time.
Speed Loop Initialization (YANK).
To
improve the acquire time of the speed control
loop, there is an automatic feature controlled by an
internal YANK signal. The motor is started at the
maximized programmed current by bypassing the
FILTER terminal. The FILTER terminal is
clamped to two diodes above ground, initializing it
near the closed loop operating point. YANK is
enabled at startup and stays high until the desired
speed is reached. Once the first error-fast occurs,
indicating the motor crossed through the desired
speed, YANK goes low. This releases the clamp
on the FILTER terminal and current control is
returned to FILTER. This feature optimizes speed
The watchdog timing function allows time to detect correct motor position
by checking the back-EMF polarity after each commutation. If the correct
polarity is not observed between t
BLANK
and t
WD
, then the watchdog timer
commutates the outputs to the next state to synchronize the motor. This
function is useful in preventing excessive reverse rotation, and helps in
resynchronizing (or starting) with a moving spindle.
Current Control.
The A8905CLB provides linear current control via the
FILTER terminal, an analog voltage input. Maximum current limit is also
provided, and is controlled in four steps via the serial port. Output current is
sensed via an internal sense resistor (R
S
). The voltage across the sense resistor
is compared to one-tenth the voltage at the FILTER terminal less two diode
drops, or to the maximum current limit reference, whichever is lower. This
transconductance function is I
OUT
= (V
FILTER
-2V
D
) / 10R
S
, where R
S
is
nominally 0.3
and V
D
is approximately 0.7 V.
YANK
SPEED-CONTROL
INITIALIZATION
POWER UP
ERROR FAST
FROM FLL
S Q
R
–
+
C
R
C
FILTER
Id
F2
F1
F1
Ic
V
DD
ERROR SLOW
FROM FLL
CHARGE
ERROR FAST
OUT
V
BB
V
DD
÷
10
SEQUENTIAL
LOGIC
C
RES
BOOST
CHARGE
PUMP
MUX
–
+
–
+
LINEAR
CURRENT CONTROL
FROM
SERIAL PORT
REGISTER
D3 AND D4
V
I
1.85 V
x1
R
S
Speed Control.
The A8905CLB includes a frequency-locked loop speed
control system. This system monitors motor speed via internal or external
digital tachometer signals, generates a precision speed reference, determines
the digital speed error, and corrects the motor current via an internal charge
pump and external filtering components on the FILTER terminal.
60 x f
OSC
desired motor speed (rpm)
Dwg. EP-046
Dwg. EP-045
SECTOR
FCOM
TACH
D5
–
D18
D19
D20 &
D21
OSC
REF
4-BIT
FIXED
COUNTER
14-BIT
PROGRAMMABLE
COUNTER
SREGISTER
COUNT
(3 x MOTOR POLES)
MUX
÷
2
REF
TACH
ERROR
FAST
ONCE-AROUND
PULSE
REF
TACH
SLOW
相关PDF资料 |
PDF描述 |
|---|---|
| 8906 | BIDIRECTIONAL 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING |
| 8909 | 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING AND POWER DMOS OUTPUTS |
| 8910 | T-1 Subminiature Lamps |
| 8920 | DUAL SCHOTTKY DIODE |
| 8925 | 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH LINEAR CURRENT CONTROL AND POWER DMOS OUTPUTS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 8905.2 | 功能描述:工业继电器 RMH1B High Current RelayModule, 5VDC, SPDT, 1Ch RoHS:否 制造商:TE Connectivity / Kilovac 触点形式:1 Form A (SPST-NO) 触点电流额定值: 线圈电压:9 VDC to 36 VDC 线圈电阻:38 Ohms 线圈电流: 切换电压: 安装风格:Panel 触点材料:Silver Palladium |
| 8905.3 | 功能描述:工业继电器 RMH4B, High Current RelayModule, 5VDC, SPDT, 4Ch RoHS:否 制造商:TE Connectivity / Kilovac 触点形式:1 Form A (SPST-NO) 触点电流额定值: 线圈电压:9 VDC to 36 VDC 线圈电阻:38 Ohms 线圈电流: 切换电压: 安装风格:Panel 触点材料:Silver Palladium |
| 89-050 | 制造商:Ideal Industries Inc 功能描述:RG6 BNC PLENM COMPR CONN |
| 8905-0.5" X 0.5"-1000 | 功能描述:3M 8905 POLYESTER TAPE - 0.5" X 制造商:3m (tc) 系列:8905 零件状态:在售 标准包装:1 |
| 8905-0.5" X 0.75"-1000 | 功能描述:3M 8905 POLYESTER TAPE - 0.5" X 制造商:3m (tc) 系列:8905 零件状态:在售 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。