- 您现在的位置：买卖IC网 > PDF目录378256 > 8905 (Allegro MicroSystems, Inc.) 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING PDF资料下载
参数资料
| 型号： | 8905 |
| 厂商： | Allegro MicroSystems, Inc. |
| 英文描述： | 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING |
| 中文描述： | 3相无刷直流电动机控制器/驱动器，反电动势遥感 |
| 文件页数： | 9/12页 |
| 文件大小： | 163K |
| 代理商： | 8905 |
8905
3-PHASE BRUSHLESS DC
MOTOR CONTROLLER/DRIVER
V
BRK
V
FAULT -
V
D
acquire and minimizes settling. The Current Control Block Diagram illustrates
the YANK signal and its effects.
Braking.
A dynamic braking feature of the A8905CLB shorts the three
motor windings to ground. This is accomplished by turning the three source
drivers OFF and the three sink drivers ON. Activation of the brake can be
implemented through the BRAKE input or through the D2 bit in the serial port.
The supply voltage for the brake circuitry is the C
RES
voltage, allowing the brake
function to remain active after power failure. Power-down braking with delay can
be implemented by using an external RC and other components to control the
brake terminal, as shown. Brake delay can be set using the equation below to
ensure that voice-coil head retract occurs before the spindle motor brake is
activated. Once the brake is activated, due to the inherent capacitive input, the
three sink drivers will remain active until the device is reset.
t
BRK
= R
B
C
B
1 – l
n
BRAKE
FAULT
VBRK
VFAULT D
–
V
BRAKE
ACTIVATED
Dwg. OP-004
RB
CB
t BRK
Centertap.
The A8905CLB internally
simulates the centertap voltage of the motor.
To obtain reliable start-up performance from
motor to motor, the motor centertap should be
connected to this terminal.
Serial Port.
The serial port functions to
write various operational and diagnostic modes
to the A8905CLB. The serial port DATA IN is
enabled/disabled by the CHIP SELECT
terminal. When CHIP SELECT is high the
serial port is disabled and the chip is not
affected by changes in data at the DATA IN or
CLOCK terminals.
To write data to the serial port, the
CLOCK terminal should be low prior to the
CHIP SELECT terminal going low. Once
CHIP SELECT goes low, information on the
DATA IN terminal is read into the shift register
on the positive-going transition of the CLOCK.
There are 24 bits in the serial input port.
Data written into the serial port is latched
and becomes active upon the low-to-high
transition of the CHIP SELECT terminal at the
end of the write cycle. D0 will be the last bit
written to the serial port.
Reset.
The RESET terminal (when pulled
low) clears all serial port bits, including the D0
latch, which puts the A8905CLB in the sleep
mode.
Dwg. EP-036-1
INDEX
CHIP SELECT
+5 V
VRET
CWD
CD2
CD1
RESET
CLOCK
DATA IN
VBB
CST
RES
0.22
μ
F
C
CF2
RF1
CF1
BYPASS
BYPASS
1
2
3
4
5
6
7
8
9
9
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
DD
V
BB
V
S
FLL
MUX
COMMUTATION
DELAY
BOOST
CHARGE
PUMP
OSC (REF)
DATA OUT
FAULT
RB
CB
TYPICAL
APPLICATION
相关PDF资料 |
PDF描述 |
|---|---|
| 8906 | BIDIRECTIONAL 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING |
| 8909 | 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING AND POWER DMOS OUTPUTS |
| 8910 | T-1 Subminiature Lamps |
| 8920 | DUAL SCHOTTKY DIODE |
| 8925 | 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH LINEAR CURRENT CONTROL AND POWER DMOS OUTPUTS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 8905.2 | 功能描述:工业继电器 RMH1B High Current RelayModule, 5VDC, SPDT, 1Ch RoHS:否 制造商:TE Connectivity / Kilovac 触点形式:1 Form A (SPST-NO) 触点电流额定值: 线圈电压:9 VDC to 36 VDC 线圈电阻:38 Ohms 线圈电流: 切换电压: 安装风格:Panel 触点材料:Silver Palladium |
| 8905.3 | 功能描述:工业继电器 RMH4B, High Current RelayModule, 5VDC, SPDT, 4Ch RoHS:否 制造商:TE Connectivity / Kilovac 触点形式:1 Form A (SPST-NO) 触点电流额定值: 线圈电压:9 VDC to 36 VDC 线圈电阻:38 Ohms 线圈电流: 切换电压: 安装风格:Panel 触点材料:Silver Palladium |
| 89-050 | 制造商:Ideal Industries Inc 功能描述:RG6 BNC PLENM COMPR CONN |
| 8905-0.5" X 0.5"-1000 | 功能描述:3M 8905 POLYESTER TAPE - 0.5" X 制造商:3m (tc) 系列:8905 零件状态:在售 标准包装:1 |
| 8905-0.5" X 0.75"-1000 | 功能描述:3M 8905 POLYESTER TAPE - 0.5" X 制造商:3m (tc) 系列:8905 零件状态:在售 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。