- 您现在的位置：买卖IC网 > Datasheet目录611 > 90075-1 (TE Connectivity)ASSY SAHT Datasheet资料下载
参数资料
| 型号： | 90075-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | ASSY SAHT |
| 标准包装： | 3 |
| 系列： | Certi-Crimp |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 端子，20-26 AWG |
| 特点： | 侧面插入，棘齿 |
408-7092
4. Position the terminal in the crimpers so that the
locator/insulation stop enters the locator slot in the
terminal.
5. Hold the terminal in this position and squeeze the
tool handles together until the insulation anvil starts
entry into the insulation crimper. Do NOT deform the
insulation barrel or wire barrel.
6. Insert a properly-stripped wire or wires through
the wire slot of the locator and into the wire barrel of
the terminal until the wire insulation butts against
the locator/insulation stop.
7. While holding the wire(s) in place, squeeze the
tool handles together until the ratchet releases.
8. Allow the tool handles to open fully and remove
the crimped terminal.
4. MAINTENANCE/INSPECTION
4.1. Daily Maintenance
Remove all foreign particles with a clean, soft brush or
a clean, soft, lint-free cloth. Make sure the proper
retaining pins are in place and are secured with the
proper retaining rings. If foreign matter cannot be
removed easily, or if the proper replacement parts are
not available, return the tool to your supervisor.
Make sure all pivot points and bearing surfaces are
protected with a thin coat of any good SAE 20 motor
oil. Do NOT oil excessively. When the tool is not in
use, keep the handles closed to prevent objects from
becoming lodged between the dies, and store the tool
in a clean, dry area.
4.2. Periodic Inspection
Regular inspection should be performed by quality
control personnel. A record of scheduled inspections
should remain with the tool and/or be supplied to the
supervisory personnel responsible for the tool. Though
recommendations call for at least one inspection a
month, the inspection frequency should be based on
the amount of use, ambient working conditions,
operator training and skill, and established company
standards. These inspections should be performed in
the following sequence:
A. Visual Inspection
1. Remove all lubrication and accumulated film by
immersing the tool (handles partially closed) into a
suitable degreaser that will not affect paint or plastic
material.
2. Make certain all retaining pins are in place and
are secured with the proper retaining rings. If
replacements are necessary, refer to Figure 5.
3. Close the tool handles until the ratchet releases,
and then allow the handles to open freely. If they do
not open quickly and fully, then the spring is
defective and must be replaced (see Section 5,
REPLACEMENT AND REPAIR).
Back of Tool (Wire Side)
Locator / Insulation Stop
Crimp Section Wire
Size Marking
Insulation Crimper
Locator Slot in Contact
Rev C
Stripped Wire
Insulation Anvil
Figure 3
2 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 90090-3 | ASSY SAHT |
| 90101-3 | ASSY SAHT |
| 90120 | DOUBLE ACTION HAND TOOL BLACK |
| 90121 | SADAHT C CRIMP 12-18 |
| 90136-1 | TOOL HAND CERTI-CRIMP II W/DIES |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 90075-1005 | 制造商:Molex 功能描述:WE PLUG HSG 6/6 9 HSG 6/6 900751005 |
| 90075-1033 | 制造商:MOLEX 功能描述:WE PLUG HSG 6/4 900751033 制造商:Molex 功能描述:WE PLUG HSG 6/4 9007 UG HSG 6/4 900751033 |
| 90075-1059 | 制造商:Molex 功能描述:HOUSING 8/8 W/O LUG W/O LUG 900751059 |
| 9007550 | 制造商:SYLVANIA 功能描述:STRIPLIGHT 221MM 30W CLEAR |
| 9007551 | 制造商:SYLVANIA 功能描述:STRIPLIGHT 221MM 30W OPAL |
发布紧急采购，3分钟左右您将得到回复。